Euro-Pro BPV325H - Manual (Page 7)

Attaching the Flexible Hose to
the Vacuum
The flexible hose should be connected
to the vacuum before strapping the unit
to your back.
1. To connect the flexible hose into the
hose inlet, insert the threaded end
of the flexible hose into the hose
inlet and turn counter-clockwise
until it locks into place. (Fig. 6)
2. Plug the power cord into the
electrical outlet.
3. To remove the flexible hose, unplug
the power cord and then turn the
hose clockwise and pull the flexible
hose out.
Attaching the Telescopic Tube to
the Flexible Hose Handle
1. Holding the telescopic tube, insert
the handle into the telescopic tube
receptacle. Push the handle in.
(Fig. 7)
Fig. 6
OPERATING INSTRUCTIONS
Note: Always remove the power plug
from the wall outlet before assembling
or removing accessories.
Manual Suction Control
Your vacuum cleaner includes a
manual variable suction control on the
flexible hose handle . The suction
power can be adjusted by moving the
suction regulator to the desired position
between Open and Closed. (Fig. 10)
Open gives you less suction, closed
maximum suction. For example, less
suction is required on upholstery and
draperies compared to thick carpets,
which require maximum suction.
Fig. 7
3. To remove the telescopic tube from
the flexible hose, press on the
telescopic tube release button and
pull it out. (Fig. 9)
Using the Floor to Carpet Brush
1. To attach the floor to carpet brush to
the telescopic tube, insert the
telescopic tube into carpet to floor
brush. (Fig. 11)
Fig. 10
Fig. 11
Floor to
Carpet
Brush
5
Plastic
Button
Fig. 8
2. Push forward on the plastic button
and pull the inner tube outward to
extend for a longer reach. (Fig. 8)
Fig. 9
Telescopic Tube
Release
OPERATING INSTRUCTIONS
8
2. Pull the tab on the HEPA dust bag
holder out slightly and flip upwards.
(Fig. 22)
3. Holding the HEPA dust bag in your
hand, slide it out from the slots in
the bag holder. Hold carefully in
order to avoid having dust fall out
of HEPA dust bag. (Fig 23)
Removing & Replacing HEPA
Dust Bag
To remove the HEPA dust bag from the
vacuum:
Important: DO NOT use the vacuum
without all filters, shake-out bag, and
with or without HEPA dust bag in place.
1. To remove the HEPA dust bag,
press on the canister lid tabs on
each side of the unit and lift canister
lid. (Fig. 22)
4. Turn the unit on by pressing the
switch located near the base of the
unit to turn the vacuum cleaner on.
(Fig. 21)
Power
Switch
Fig. 21
Fig. 22
Canister
Lid Tabs
Canister
Lid Tabs
Fig. 23
Tab
Dust
Bag
Holder
5. To blow up inflatable items, select the
appropriate size blower attachment that
will fit into the air valve. (Fig. 19)
Fig. 19
6. Turn the unit on and hold the blower
attachment and air valve while the
vacuum exhaust is pumping air into
the inflatable.
7. To detach the flexible hose turn
clockwise and pull out from blower
port.
Note : Firmly hold the flexible hose by the
attachment when blowing dirt or dust off of
objects.
Using Your Vacuum
Warning:
To reduce the risk of electric
shock, the power cord must be
disconnected before removing the dust
bag, shake-out bag, changing the
filters or performing maintenance or
trouble-shooting checks.
1. Insert the power plug into the wall
outlet.
2. Connect hose and telescopic tube if
desired.
3. Correctly place shoulder straps on
each shoulder and secure the waist
band with hook and loop strips.
(Fig. 20)
Caution : If the waist band and both
shoulder straps are not properly and
securely in place the unit could fall off
your back causing damage or injury.
Fig. 20
Shoulder
Strap
Shoulder
Strap
Waist
Band
&
Tool
Storage