RISCO Group Wireless 2-Way Slim Keypad - Manual

F R A N Ç A I S
Introduction
The Wireless 2-Way Slim Keypad comes in two models:
RW132KL1P—a black protection-insulated outdoor model empowered with a proximity reader
RW132KL2P — a white indoor model
operates in either of two modes:
• Full function Mode: Wireless LED operating keypad
• Bypass unit Mode: Used to activate an entry countdown period
Being bi-directional the 2-Way keypad receives a reply status indication from the panel
for each command that it has sent to the panel.
To use functions of the keypad you can use a proximity tag or a code.
Main Features
• Bi-directional wireless communication
• Up to three wireless keypads per system
• Power-save light sensor
• Proximity tag operation
• Wall tamper protection
• Battery economy mode
• Wireless doorbell function
• 2 operation modes
• Outdoor-certi
¿ed IP65 (RW132KL1P only)
COMMUNICATION SETUP
The 2-Way Slim Outdoor Keypad must identify itself to the system receiver. This can be
done by entering the 11-digit serial number of the keypad into the system or using RF mode.
Setup communication:
1. Set the system to Learn Mode by RF or by Code.
2. Send an allocation message *.
• By RF communication: Send a Write message by pressing both keys
simultaneously for at least 2 seconds.
• By Code: Enter the keypad's 11-digit serial code number
3. The system automatically recognizes the device and allocates it the next available
index number. The system will announce the keypad device type and the index it has
been allocated to.
4. If required to change the keypad's default settings, con gure the keypad's parameters
according to the system installation manual.
* Note: Add the keypad to the system remotely using the Con guration Software.
* Note: Before mounting the keypad, test the keypad communication with the system.
UK
Tel: +44-(0)-161-655-5500
[email protected]
U.S.A
Tel: +1-631-719-4400
[email protected]
ITALY
Tel: +39-02-66590054
[email protected]
BRAZIL
Tel: +1-866-969-5111
[email protected]
SPAIN
Tel: +34-91-490-2133
[email protected]
CHINA (Shanghai)
Tel: +86-21-52-39-0066
[email protected]
CHINA (Shenzhen)
Tel: +86-755-82789285
[email protected]
FRANCE
Tel: +33-164-73-28-50
[email protected]
POLAND
Tel: +48-22-500-28-40
[email protected]
BELGIUM
Tel: +32-2522-7622
[email protected]
ISRAEL
Tel: +972-3-963-7777
[email protected]
Wireless 2-Way Slim Keypad
RISCO Group 08/2013 5IN1926 C
EN50131-1, EN50131-3, Grade 2
EN50130-5, Environmental class IV (RW132KL1P),
Environmental class II (RW132KL2P)
EN50131-6, Type C
PD6662:2010
RTTE Compliance Statement:
Hereby, RISCO Group declares that this equipment is in compliance with the essential requirements and
other relevant provisions of Directive 1999/5/EC. For the CE Declaration of Conformity please refer to our
website: www.riscogroup.com
Remove locking pin
securing the mounting
bracket to the unit.
1
Separate the
mounting
plate
from the
keypad's
main
unit.
2
3
Mount the
bracket to
the wall
using the
supplied
screws.
Release the battery cover
screw and place the
supplied two batteries.
Pay attention to polarity.
4
5
A. Close the battery
compartment.
B. Mount the keypad
to the bracket (B)
A B
LED Indicator
Color State Status
Blue Blink During communication with
the panel
Red
On System fully or partially set
Slow ash During Exit delay
Rapid ash During Alarm
Green Blink Fault indication in the system
while the system is unset*
Green/Red Toggle Waiting for code to be entered.
Blue Red Green
USING THE PROXIMITY TAG
The proximity tag, is correctly used by
applying it within a 2 cm (two centimeter)
distance from the key
as shown at right
(after waking the keypad by pressing the
appropriate key).
RW132KL1P RW132KL2P
Buzzer Indication:
Duration Operation
Long beep Con ¿tmation
3 short beeps Wrong code
Pulsed beeps Exit/Entry beeps (programmable)
Short beep Each key press
Rehov Hahoma 14
Rishon Lezion, Israel