Marshall Electronics CV360-CGB - Manual (Page 8)

- 8 -
9. DIS : Digital Image Stabilizer function
<
OFF /ON > ◀
1) RANGE : Maximum stabilizer Range
(Up to 30% is a range of the input Image in accordance with the
digital zoom is set up to 1.4 times the required use.)
< 10% ,20%,30% >
2) FILTER : Select “High” is more sensitive (Correction is not good)
< LOW/
MIDDLE /HIGH >
3) AUTO C : Such as vibration like High Frequency is be Correction, Such as
vibration like Low Frequency is be the screen functions to be
move naturally.
① FULL : During movement, it is always corrected to be positioned
at the center of image direction
② HALF : The Center Correction region Full Compensation is fixed
and Periphery only compensation
< OFF/
HALF /FULL >
10. MOTION : Select On to activate motion detection, surveillance box on/off
< OFF /ON > ◀
1) SENSITIVITY : Select the level of sensitivity detected in surveillance
< 0~20 steps,
3 >
2) DET H-POS : Set to move Detection area box into left and right
< 0~20 steps,
0 >
3) DET V-POS : Set to move Detection area box into up and down.
< 0~20 steps,
0 >
4) DET H-SIZE: Set Detection area box’s size into right and left
< 0~20 steps,
60 >
5) DET V-SIZE : Set Detection area box’s size into up and down
< 0~20 steps,
34 >
6) MOTION OSD : On/Off the Motion detection control box
< OFF /ON >
7) ALARM : Using the Alarm device and the connect with Port GPIO
<
OFF /ON >
10) PRIVACY : Set the range of privacy protection zone ◀
① BOX : The use of the privacy function to the Box mode
< OFF /ON > ◀
1] ZONE NUM : Select to the desired box
< 0~7 steps,
0 >
2] ZONE DISP : Set the position and size that User want to value
<
OFF /ON > ◀
3] H-POS : The Select box move to the right and left
< 0~60 steps,
12 >
4] V-POS : The Select box move to the up and down
< 0~40 steps,
2 >
5] H-SIZE : The size of the selected box is adjusted to the right and left
< 0~40 steps,
3 >
6] Y-SIZE : The size of the selected box is adjusted to the up and down
< 0~40 steps,
3 >
7] Y LEVEL : The value of the box is between black and white
(“0” is black and “20” is white)
< 0~20 steps,
10 >
8] CB LEVEL : The value of the box is between green and blue
(“0” is green and “20” is blue)
< 0~20 steps,
10 >
9] CR LEVEL : The value of the box is between green and red
(“0” is green and “20” is red)
< 0~20 steps,
10 >
10] TRANS : Set the transparency
< 0~3 steps,
2 >
② POLYGON : The use of the privacy function to the customer mode
< OFF /ON > ◀
1] ZONE NUM : Select to the desired box
< 0~7 steps,
0 >
2] ZONE DISP : Set the position and size that User want to value
<
OFF /ON > ◀
3] POS0-X : Adjust the left and right of the top left corner
< 0~121 steps,
80 >
4] POS0-Y : Adjust the up and down of the top left corner
< 0~69 steps,
5 >
5] POS1-X : Adjust the left and right of the top right corner
< 0~121 steps,
88 >
6] POS1-Y : Adjust the up and down of the top right corner
< 0~69 steps,
5 >
7] POS2-X : Adjust the left and right of the bottom right corner
< 0~121 steps,
88 >
6] POS2-Y : Adjust the up and down of the bottom right corner
< 0~69 steps,
13 >
8] POS3-X : Adjust the left and right of the bottom left corner
< 0~121 steps,
80 >
9] POS3-Y : Adjust the up and down of the bottom left corner
< 0~69 steps,
13 >
10] Y LEVEL : The value of the box is between black and white
(“0” is black and “20” is white)
< 0~20 steps,
10 >
11] CB LEVEL : The value of the box is between yellow and blue
(“0” is yellow and “20” is blue)
< 0~20 steps,
10 >
12] CR LEVEL : The value of the box is between blue and pink
(“0” is blue and “20” is pink)
< 0~20 steps,
10 >
13] TRANS : Set the transparency
< 0~3 steps,
2 >