Initial use, Maintenance, cleaning and care, Changing the water – Livarno Z30591A-BS User Manual
Page 25
25
GB/MT
Assembly and Initial Use / Maintenance, Cleaning and Care
j
Make sure that the rubber seal
12
completely
covers the hole, otherwise the water could leak
from the glass sphere
1
.
j
Make sure that you have inserted the mist
generator
8
into mist generator holder
17
before you switch the tabletop mister on.
j
Insert the attachment
10
with the pointed end
into the retainer
7
of the holder
6
.
j
Place the mist generator
8
in the holder
6
and put this in the glass sphere
1
.
j
Please ensure that the mains lead
2
does not
lie across the mist generator
8
, as then no mist
is generated. In this case pull a small amount of
the mains lead
2
through the rubber seal
12
.
Note: The position of the mist generator
8
affects the quantity of mist generated. The best
results are obtained if you position the mist
generator
8
as shown in Illustration A.
j
Check whether the glass sphere
1
is posi-
tioned correctly on the glass sphere stand
4
(marking line
5
facing downwards).
j
Adjust the angle of the opening of the glass
sphere
1
in order to prevent the water from
overflowing.
j
Fill the glass sphere
1
with approx. 1600 ml of
water.
Note: Fill the glass sphere
1
up to the Max.
mark
11
only.
Note: The best result is obtained if the water
is just above the water level sensor
9
.
Note: The mist generator
8
switches off au-
tomatically if the water level falls below the water
level sensor
9
. In addition, a red LED light bulb
will light up on the water level sensor
9
when
the water level falls below the water level
sensor
9
.
Note: Do not use fragrance oil.
Q
Initial Use
j
Connect the connection plug
3
to the adapter
plug
14
and insert the mains adapter
13
into
a socket (230 V – 240 ~, 50 Hz).
Note: Please ensure that the mains adapter
13
is located outside of the mist that is generated.
j
The mist generator
8
begins to generate a
fine spray of water which looks like smoke. The
LEDs
15
light up and automatically change
their colour.
j
If the tabletop mister is only generating a little
or no mist, please add more water.
j
If the tabletop mister is only generating water
spray or no mist will be produced, the water is
probably dirty. It should then be replaced (see
"Changing the Water").
j
Turn the tabletop mister off by removing the
mains adapter
13
from the socket.
Q
Maintenance, Cleaning and Care
WArNING!
DANGEr OF DEAtH FrOM
ELECtrIC SHOCK! Always remove the mains
adapter
13
from the socket before performing any
work on the product.
Q
Changing the Water
j
Change the water at least once a week. This
prevents the formation of algae.
j
Pour out the water and allow the tabletop mis-
ter to dry completely if you are not going to
use it for a prolonged period.
j
Dirty water impairs / prevents the correct func-
tioning of the mist generator
8
. If the device is
only producing water spray or if the quantity of
mist is less than usual, replace the water in the
glass sphere
1
.
j
Remove the mains adapter
13
from the socket.
Disconnect the connection plug
3
and adapter
plug
14
.
m CAUtION! It is essential to hold the glass
sphere
1
over a wash basin. Water might
drain / spill out of the glass sphere
1
.
j
Remove the mist generator
8
and the holder
6
from the glass sphere
1
. Pull the rubber seal
12
out of the small hole in the glass sphere.
j
Pour the water out and clean the glass sphere
1
.
j
Reassemble the tabletop mister as described
under "Assembly and Initial Use".