Powerplus POW8136 TELESCOPIC MITRE SAW 2000W 255M +SUPPORT STAND EN - Manual (Page 8)

POW8136 EN
Copyright © 2014 VARO P a g e | 8 www.varo.com
 Re-tighten the locking handle to lock the turntable (8) into place.
 Cut as described under section10.2.
10.4 Mitre cuts 0°-45° and rotary table 0° (Fig. 4/7)
 The POW8136 can be used to make mitre cuts of 0°-45° relative to the machine bed on
the left side.
 Lift the machine head (4) to its top position.
 Fix the rotary table (8) in 0° position.
 Undo the locking nut (13) and, holding the handle (2), tilt the machine head (4) to the left
until the pointer (23) coincides with the required angle dimension (15).
 Re-tighten the locking nut (13) and make the cut as described in Section 10.2.
10.5 Precision adjustment of the stop for 45° mitre cuts (Fig. 2/4/8)
 Lower the machine head (4) and fix with the lock pin (16).
 Fix the rotary table (8) in 0° position.
 Undo the locking nut (13) and, holding the handle (2), tilt the machine head (4) to the left
by 45°
 Place the 45° stop angle (b) between the saw blade (5) and the rotary table (8).
 Slacken the counter nut and adjust the setting screw (22) until the angle between the saw
(5) and the rotary table (8) equals exactly 45°.
 Re-tighten the locking nut (13) and make the cut as described in Section 10.2.
10.6 Mitre cuts 0-45 and rotary table 0°-45° (Fig. 4/9)
 The POW8136 can be used to make mitre cuts on the left at an angle of 0°-45° relative to
the work top and 0°-45° relative to the stop rail.
 Lift the machine head (4) to its top position.
 Release the turntable (8) by loosening the locking grip .
 Adjust the rotary table (8) by its handle (2) to the required angle (see also Section 7.4).
 Re-tighten the locking handle to fix the rotary table in position.
 Undo the clamping nut (13) and, holding the handle (2), tilt the machine head (4) to the left
to the required angle dimension
 (see also Section 10.5).
 Re-tighten the locking nut (13) and make the cut as described in Section 10.2.
10.7 Locking lever (13)
You can lock the machine into the desired angle by using the locking lever (13). This lever
needs to be turned 360° to the left to safely lock the machine into place. Because of the shape
of the frame, the lever cannot make this turn in one go. Please turn the lever 90° to the left.
Pull the lever out towards you and bring it back to its original position. Repeat this a few times
until the machine is safely locked.
11 CHIP EXTRACTION (FIG. 1)
The saw is equipped with a chip collection bag (24). The chip bag (24) can be emptied by
opening the zip fastener at the bottom.
12 REPLACING THE SAW BLADE (FIG. 11)
 Pull out the power plug.
 Swing up the machine head (4).
 Press the lever and swing up the saw blade guard to the point where the recess in the saw
blade guard is above the flange bolt.
 Press the saw shaft lock (17) with one hand while holding the wrench (31) on the flange
bolt with the other.
 Firmly press on the saw shaft lock (17) and slowly rotate the flange bolt in clockwise
direction. The saw shaft lock engages after no more than one rotation.
 Now, using a little more force, slacken the flange bolt in clockwise direction.