Lanner FW-6436 - Manual (Page 13)

10
Motherboard Information
Chapter 4
Network Application Platforms
Reset Button Connector (JRST_BTN1): a 2-pin header
for connecting the reset switch. It can be either a
hardware or a software reset depending on the BIOS
setting. It serves the same function as the Front
Panel Reset Switch (SW_RST_BTN1).
2-Pin Power Button Connector (JPWBTN1)
CompactFlash Connector (CF1): It is for connecting a
Compact Flash card to be served as your system’s
storage. The connector is a CF Type II slot which could
fit both CF Type I or CF Type II cards.
PIN DESCRIPtION PIN DESCRIPtION
1 GND 26 CD1-
2 DAtA3 27 DAtA11
3 DAtA4 28 DAtA12
4 DAtA5 29 DAtA13
5 DAtA6 30 DAtA14
6 DAtA7 31 DAtA15
7 CE1# 32 CE2#
8 A10 33 VS1#
9 OE# 34 IOR#
10 A9 35 IOw#
11 A8 36 wE#
12 A7 37 READY#
13 CFVCC3 38 CFVCC3
14 A6 39 CSEL
15 A5 40 VS2#
16 A4 41 RESEt
17 A3 42 wAIt#
18 A2 43 INPACK#
19 A1 44 REG#
20 A0 45 DASP#
21 DAtA0 46 DIAG#
22 DAtA1 47 DAtA8
23 DAtA2 48 DAtA9
24 wP 49 DAtA10
25 CD2- 50 GND
Jumper Settings
CMOS Jumper (CMOS1): It is for clearing the CMOS
memory and system setup parameters by erasing
the data stored in the CMOS RAM such as the system
password.
USB 2.0 Ports (J2): This port is for connecting the USB
module cable. The high-speed USB port complies
with USB2.0 and support up to 480 Mbps connection
speed. It is.
Dual USB 2.0 Ports (USB1): This provides two USB 2.0
ports in the front panel.
Keyboard and Mouse Interface Connectors (PKMB1):
a 2 x 4 pin header for connecting the PS/2 keyboard
and mouse interface cable.
PIN NO. Function
1-2 Normal (Default)
2-3 Clear CMOS
Pin No. Function
1 USB_VCC
2 USBD0-
3 USBD0+
4 GND
5 USB_VCC
6 USBD1-
7 USBD1+
8 GND
1
2
3
1 2 3 4
5 6 7 8
2
4
6
8
1
3
5
7
Pin No. Function
1 VCC
2 MSCLK
3 MSDAtA
4 KEY
5 KBDAtA
6 KEY
7 GND
8 KBCLK
PIN NO. Function
1-2 PwRBtN
2-3 Ground
2
1
2
1
PIN NO. Function
1 RSt_BtN
2 Ground
1......................25
26...................50
9
7
5
3
1
10
8
6
4
2
Pin No. Function
1 USB_VCC
2 Ground
3 Key
4 USBD3+
5 USBD2-
6 USBD3-
7 USBD2+
8 Key
9 Ground
10 USB_VCC