Thunder Tiger RapRaptor E820 - Manual (Page 7)

-6-
Main Rotor System / 主旋翼機構組裝
Bag A
Apply threadlocker
使用螺絲防鬆膠 Assemble left and right side the same way
左右側組件相同
BEARING, d8xD16xW5
滾珠軸承, d8xD16xW5
THRUST BEARING,
d8xD16xW5
止推軸承, d8xD16xW5
THRUST COLLAR,
d8xD12xW0.5
止推軸環, d8xD12xW0.5
SOCKET SCREW, M3x6
內六角螺絲, M3x6
LINKAGE BALL(A)
內六角連接頭螺絲(A)
WASHER, d3xD8xW1.4
墊圈, d3xD8xW1.4
SOCKET SCREW, M3x12
內六角螺絲, M3x12
Apply grease
使用潤滑油膏(黃油)
Assemble the main rotor pitch housing as drawing
主旋翼轉座組裝圖
The bearings come with the grips which had been
assembled by Factory.
主旋翼夾座內軸承已由原廠壓配完成。
(1-1) (1-1)
(1-2)
(1-3)
No.
1
1-1
1-2
1-3
2
3
4
Qty
2
2
1
1
2
4
2
Description 名稱
METAL ROTOR GRIP SET
BEARING, d8xD16xW5
THRUST BEARING, d8xD16xW5
THRUST COLLAR, d8xD12xW0.5
FBL ROTOR GRIP LEVER
SOCKET SCREW, M3x6
ROTOR GRIP POST 金屬主旋翼轉座組
滾珠軸承,d8xD16xW5
止推軸承, d8xD16xW5
止推軸環, d8xD12xW0.5
無平衡翼金屬旋翼轉座搖臂
內六角螺絲, M3x6
金屬主旋翼轉座支柱
No.
5
6
7
8
9
10
Qty Description 名稱
LINKAGE BALL(A)
WASHER, d3xD8xW1.4
SOCKET SCREW, M3x12
METAL SWASHPLATE
SWASHPLATE POST
LINKAGE BALL 內六角連接頭螺絲(A)
墊圈, d3xD8xW1.4
內六角螺絲, M3x12
十字盤組
十字盤球型支柱
大球頭 6
2
2
1
2
1
(5)
(4)
(2)
(6)
(7)
(3)
(3)
(1)
Large Internal Diameter always goes toward
the Main Rotor Hub
內徑較大的一側，面向主旋翼固定座組(內側)。 Small Internal Diameter always goes
toward the Blade
內徑較小的一側，面向主旋翼組(外側)。
Checking Tips: >
轉動角度： >
（轉動角度大者，內孔大；轉動角度小者，內孔小）
Diagram for Thrust Bearing Assembly
止推軸承安裝示意圖
(5)
(8)
(5)
(10)
(5)
(9)
(9)
(5)
LINKAGE BALL
大球頭
DO NOT over tighten the linkage
ball while securing in order to
avoid the screw broken.
鎖固時，切勿過度迫緊連接頭螺絲
以避免螺牙段斷裂。
Secure all screws shown on this page with a drop of threadlocker.
本頁顯示之螺絲請使用適量防鬆膠鎖固。