Studio Technologies 5110 V.3.2 - Manual (Page 13)

Model 5110 User Guide Issue 7, October 2014
Studio Technologies, Inc. Page 13
Model 5110
Mic/Line Input Module
Specifications
Mic/Line Inputs: 2
Input Sensitivity, 15 dB Steps (Default):
selectable for line (0 dB), 15, 30 or 45 dB gain
Input Sensitivity, 3 dB Steps (Selected via GUI):
selectable for line (0 dB), 9 to 60 dB in 3 dB steps
Maximum Input Level: +24 dBu
Type: electronically balanced
Impedance: approximately 3 k ohms
CMRR: 61 dB at 60 Hz
Channel-to-Channel Crosstalk: <–106 dB at
10 kHz
Phantom Power: 48 volts DC, nominal, meets
IEC 61938 P48 standard
Digital Audio Output: 1 (2-channel)
Type: AES3, unbalanced, 75 ohms
Sample Rate/Bit Depth: 48 kHz/24
Frequency Response: ±0.2 dB, 20 Hz to 20 kHz
Dynamic Range (A Weighted): 112 dB, input
sensitivity set for Line (0 dB gain), 15 dB gain, or
30 dB gain; 103 dB at 45 dB gain
Distortion: 0.0008% (–101 dB) with output at
–1 dBFS, 22 Hz to 22 kHz, 30 dB gain
Nominal Output Level: –20 dBFS (Model 5110S);
–18 dBFS (Model 5110E)
Analog Audio Outputs: 2
Type: electronically balanced, capacitor-coupled,
intended to drive balanced loads of 2 k ohms or
greater
Nominal Level: +4 dBu (Model 5110S), 0 dBu
(Model 5110E)
Maximum Level: +24 dBu into 10 k ohms
Source Impedance: 200 ohms, nominal, differential
Frequency Response: ±0.5 dB, 20 Hz to 16 kHz;
–1.5 dB at 20 kHz)
Dynamic Range (A Weighted): 107 dB, input
sensitivity set for Line (0 dB gain), 15 dB gain, or
30 dB gain; 102 dB at 45 dB gain
Distortion: 0.002% (–93 dB) with output at
+23 dBu, 22 Hz to 22 kHz, 30 dB gain)
Meters: 2, 7-segment LED, modified VU ballistics
Remote Control Capability: mic gain, phantom
power, pushbutton switch lock out. Requires remote
access module for implementation.
Connectors:
Mic/Line Inputs: 2, 3-pin female XLR, no latch
AES3 Digital Audio Output: 1, DIN 1.0/2.3-
compliant coaxial
Analog Audio Outputs: 1, 5-position male header.
Refer to Appendix A for mating connector details.
DC Input/Data: 1, 4-position male header. Refer
to Appendix A for mating connector details.
Power Requirement: 12 volts DC nominal,
300 milliamperes max; acceptable range 10-18
volts DC, 330 milliamperes max at 10 volts
Dimensions (Overall):
3.75 inches wide (9.5 cm)
1.69 inches high (4.3 cm)
2.30 inches deep (5.8 cm)
Mounting: requires custom implementation;
no mounting method provided. Refer to Appendix B
for details.
Weight: 0.2 pounds (91 g)
Specifications and information contained in this
User Guide subject to change without notice.