beautypg.com

Sand plow installation, Accessories – Smithco AFC Sport Truck (sn AFT1032 – AFT1036) Operator Manual User Manual

Page 51

background image

49

Accessories

52-005 60" MANUAL PLOW

REF#

PART#

DESCRIPTION

QUANTITY

1

HB-38-16-225

Bolt,

3

/

8

-16 x 2

1

/

4

2

HNTL-38-16

Lock Nut,

3

/

8

-16

2

2

52-032

Plow Lift

1

HG-18-180

Grease Fitting,

1

/

8

x 180°

1

3

HCP-12-250

Clevis Pin,

1

/

2

x 2

1

/

2

2

HHP-18

Bridge Pin,

1

/

8

2

4

52-040

Left Plow Lift Arm

1

5

HB-38-16-275

Bolt,

3

/

8

-16 x 2

3

/

4

4

HNTL-38-16

Lock Nut,

3

/

8

-16

4

6

27-049

Left Pusher Bar

1

7

HB-38-16-125

Bolt,

3

/

8

- 16 x 1

1

/

4

2

HW-38

Washer,

3

/

8

4

HNTL-38-16

Lock Nut,

3

/

8

- 16

2

8

HB-12-13-300

Bolt,

1

/

2

- 13 x 3

2

HNTL-12-13

Lock Nut,

1

/

2

- 13

2

9

35-011

Aluminum 60" Plow Blade

1

10

35-012

Wear Blade

1

11

HB-38-16-100

Bolt,

3

/

8

- 16 x 1

5

HNFL-38-16

Flange Lock Nut,

3

/

8

- 16

5

12

27-050

Right Pusher Bar

1

13

52-039

Right Plow Lift Bar

1

14

HCP-12-150

Clevis Pin,

1

/

2

x 1

1

/

2

2

HHP-18

Bridge Pin,

1

/

8

2

15

52-037

Plow Lift Handle

1

8842-3

Foam Tape, 3"

1

16

15-019

Round Grip

1

SAND PLOW INSTALLATION

1.

Assemble Pusher Bars to Plow using (Ref# 7 and 8) hardware. There is a slot to bolt (Ref# 7) hard-

ware in. Sliding the bolt closest to the blade will result in a shallow cut, whereas using the end of the slot
furthest from the blade will result in a deeper cut.

2.

Bolt the (Ref# 2) Lift Assembly to the Main Frame below the front of the console using (Ref# 1)

hardware .

3.

Attach the (Ref# 15) Lift Handle to the lift assembly using (Ref# 14) hardware.

4.

Attach the right and left plow lift arms (Ref# 4 and 13) to the lift assembly (Ref# 2) using the (Ref# 3)

clevis pins.

5.

Slide Plow under machine and connect to machine. Use (Ref# 14) Clevis Pin and Bridge Pin.

6.

Lift up the plow and attach the right plow lift Arm (Ref# 13) then do the same with the left.

7.

Tighten all hardware and make sure bridge pins are in all clevis pins.

8.

We include 3" of foam tape to be placed on the lift handle where it rests on the floorboard when in the

down position.

This manual is related to the following products: