Full version manual, Cross, Trail – SILVA Cross Trail II User Manual

Page 2

visit: www.silva/enviroment
for more information about the
Waste electrical and electronic
equipment (Weee) Directive.

Thank you for choosing Silva Cross Trail II headlamp. This headlamp

can, thanks to the modular design, also be used on a helmet or on a

bike handle bar.

The Cross Trail II headlamp is equipped with Intelligent Light

which is a light distribution technology that combines a wide angle

flood light with a long reach spot light. This unique light image gives

the user peripheral and long distance vision at the same time. For a

runner, cross country skier, mountain biker or night orienteer this

translates into less head movement, increased control, better bal-

ance and more speed.

Product overview

The Cross Trail II headlamp consists of the following parts:

• Headlamp body

• Headband

• Battery belt

• Helmet bracket with adhesive strip

• Bike bracket

• Extension cable

• Battery case with attachment strap

• 4 pcs AA alkaline batteries

• Quick guide

BeFore uSe

inSert BatterieS

Cross Trail II comes with a separate battery case. Insert the bat-

teries by opening the battery lid on one of the short sides. Place the

batteries according to the image on the side of the case.

adjuSt the headBand

The elastic headband is designed to give a comfortable fit at speed

during activities such as running, XC skiing etc. Adjust the headband

by moving the sliding buckle to fit it onto your head.

Flexible battery carrying

The battery pack can be carried in multiple ways; for example in

a pocket, backpack, on the waist or mounted on the bike frame by

using the integrated strap.

Modular SySteM

In order to move the headlamp body from the headband to either the

helmet bracket or the bike bracket, gently press the release button

(located on top of the headlamp on the left hand side) forward while

lifting the headlamp body. Insert the headlamp body in the bracket

and gently press it down until you hear a click sound.

Mounting the helMet Bracket

The helmet bracket comes with pre mounted adhesive on the back

for easy mounting on any helmet. The adhesive is a polyethylene

foam tape developed to not damage or cause any type of weakness

to plastic.

Before mounting the helmet bracket on a helmet, make sure the

surface is dry and clean. Remove the protective paper from the ad-

hesive tape on the helmet bracket. Gently press the helmet bracket

to the helmet.

Mounting the Bike Bracket

The bike handlebar bracket is developed for use on bike handlebars

with a dimension between 25 and 32 mm. Included with the bike

handle bar attachment are 3 rubber inserts. Use these to ensure the

correct fitting for your bike and tighten the bottom screw to secure it

on to the handlebar.

during uSe

Switch on your headlaMP

On the side of the headlamp body there is a push button which

controls all light modes.

Available light modes: Max, Mid, Min, Wide, Blink

Each press on the button gives you the following light:

1. Turns the headlamp ON with all LEDs in maximum power.

2. Goes to Mid mode

3. Goes to Min mode

4. Goes to Wide mode

5. Starts over from 1 – Max mode

To turn OFF the headlamp; press and hold the button for 2 seconds.

The flash function, which is used to attract attention, is started from

OFF mode by pressing and holding the button for 2 seconds. To turn
OFF; press and hold the button for 2 seconds.

teMP control

The headlamp temperature will increase during use. The headlamp

temperature is mainly depending on light mode, ambient tempera-

ture and the airflow (speed). The Cross Trail II headlamp is equipped

with a temperature control function which prevents the headlamp

body from overheating by reducing the power to the LEDs. This

means that the lower the ambient temperature, the stronger the

light output.

note: always make sure that the batteries are disconnected when

the headlamp is stored in a closed compartment such as a bag,

pocket or similar.

Battery indication

When the headlamp is turned off a small LED is turned on inside the

front of the headlamp to indicate the status of the batteries. The bat-

tery status indication LED will be on for 5 seconds after power off.

Green light – Battery in good condition (more than 70% remaining)

Orange – Medium (30%-70% remaining)

Red – Battery in poor condition (Less than 30% remaining)

aFter uSe

Maintenance

To make sure you get maximum performance from your Cross Trail

II headlamp, clean it regularly with a damp cloth.

Headset cleaning – wash in washing machine at 40º C.

technical SPeciFicationS

Weight: headlamp (including head bracket): 80g

Battery pack with batteries: 130g

Battery type: 4pcs AA alkaline batteries

Light distance (Max/Mid/Min/Wide): 90m/60m/40m/20m

Lumen (Max): 250 Lumen

Burn time: Max/Mid/Min/Wide: 5h30min/15h/30h/100h

Water resistance: IPX6

Material head lamp body: PC/ABS and Aluminium

Operative temperature range: -20º - +60º C

Protect the environMent.

Headlamp and batteries should be recycled and must not be thrown

in the regular trash. Dispose these items in accordance with appli-

cable local regulations.

warranty

Silva warrants that, for a period of two (2) years, your Silva Product

will be substantially free of defects in materials and workmanship

under normal use. Silva’s liability under this warranty is limited to

repairing or replacing the product. This limited warranty extends

only to the original purchaser.

If the Product proves defective during the Warranty Period please

contact the original place of purchase. Make sure to have your proof

of purchase on hand when returning the product. Returns cannot

be processed without the original proof of purchase. This warranty

does not apply if the Product has been altered, not been installed,

operated, repaired, or maintained in accordance with instructions

supplied by Silva, or has been subjected to abnormal physical or

electrical stress, misuse, negligence or accident. Neither does the

warranty cover normal wear and tear. Silva is not responsible for any

consequences, direct or indirect, or damage resultant from use of

this product. In no event will Silva’s liability exceed the amount paid

by you for the product. Some jurisdictions do not allow the exclusion

or limitation of incidental or consequential damages, so the above

limitation or exclusion may not apply to you. This Warranty is valid

and may be processed only in the country of purchase.

For more information please visit www.silva.se

full version manual

cross

trail

art.no 39024