Monster PRT 100 MC - Manual (Page 3)

ENGLISH ENGLISH
4 5
C. Do not place any antenna near overhead
power lines or any other power circuit.
Do not touch any power line or power circuit.
Doing so may cause severe physical injury
or possibly death.
WArninG—Liquid: Avoiding
electrical Shocks
A. Do not operate your Monster Central ®
device if liquid of any kind is spilled onto
or inside the unit.
B. Do not operate your Monster Central ®
device near rain or water that’s spilled or
contained (e.g., bathtub, or kitchen sink).
WArninG—Power Cord Safety
A. When routing your Monster Central ® device’s
AC power cord, do not place it near heavy
foot traffic areas (e.g., hallways, doorways,
and floors). Do not create a trip hazard with
the power cord.
B. If your power cord’s protective jacket
begins to rip or fray, exposing the internal
wiring, shielding, etc., disconnect it from
the AC power source and discontinue use
of the Monster Central
® device immediately.
See the Warranty Information section of this
owner’s manual for important details.
WArninG—no user Serviceable
Parts inside
If, for any reason, your Monster Central ® device
is not operating properly, do not remove any part
of the unit (cover, etc.) for repair. Unplug the unit
and consult the Warranty Information section
of this owner’s manual for important details.
CAution—exposure to Heat
Do not expose your Monster Central ® device
to direct sunlight or place it near wall heaters,
space heaters, or any enclosed space prone
to temperature increase.
CAution—Proper Cleaning
In general, the only cleaning necessary for
your Monster Central
® device is a light dusting.
Unplug your component from the wall outlet
before cleaning it. Do not use any type of liquid
or aerosol cleaners.
fCC notiCe
fCC iD: y4B-AiC-eGW
(for Monster Central ® Gateway /
100MC KIT / 300MC KIT)
fCC iD: y4B-MSt-rfM
(for Monster Central ® 100 MC / 300 MC /
100MC KIT / 300MC KIT)
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses
and can radiate radio frequency energy and,
if not installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is no
guarantee that interference will not occur in
a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning
the equipment off and on, the user is encouraged
to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the
equipment and receiver
• Connect the equipment into an outlet
on a circuit different from that to which
the receiver is connected
• Consult the dealer or an experienced
radio/TV technician for help
fCC Warning
Changes or modifications not expressly approved
by Monster, Inc. could void the user’s authority
to operate the equipment.
fCC radiation exposure Statement
To comply with FCC RF exposure compliance
requirements, the antenna used for this
transmitter must be installed to provide
a separation distance of at least 20 cm from
all persons and must not be co-located or
operating in conjunction with any other
antenna or transmitter.
fCC Modular Approval Statement
This equipment is sold only to OEM integrators
and must be installed by the OEM or OEM
integrators under the following conditions:
1. The antennas used for this transmitter must
be installed to provide a separation distance
of at least 20 cm from all persons and
2. The transmitter must not be co-located with
any other antenna or transmitter.
fCC Label
This device complies with part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired operation.
inDuStry CAnADA
iC: 10122A-fALeGW
(for Monster Central ™ Gateway /
100MC KIT / 300MC KIT)
iC: 10122A-MStrfM
(for Monster Central ™ 100 MC / 300 MC /
100MC KIT / 300MC KIT)
This device complies with Industry Canada
licence-exempt RSS standard(s). Operation
is subject to the following two conditions:
(1) this device may not cause interference,
and (2) this device must accept any interference,
including interference that may cause undesired
operation of the device.
Under Industry Canada regulations, this radio
transmitter may only operate using an antenna
of a type and maximum (or lesser) gain approved
for the transmitter by Industry Canada. To reduce
potential radio interference to other users, the
antenna type and its gain should be so chosen
that the equivalent isotropically radiated power
(e.i.r.p.) is not more than that necessary for
successful communication.