Marantz AV8003 - Manual (Page 54)

CONNECTIONS
SETUP
BASIC
OPERA
TION
REMOTE
CONTROLLER
TROUBLESHOOTING
OTHERS
NAMES AND
FUNCTION
ADV
ANCED
OPERA
TION
50
ENGLISH
RDS OPERATION
Now in use in many countries, RDS (Radio Data
System) is a description of the station’s programming
hidden space in the FM signal.
Your new unit is equipped with RDS to assist in the
selection of FM stations using station and network
names, rather than broadcast frequencies. Additional
RDS functions include the ability to search for
programme types.
RADIO TEXT
Some RDS stations broadcast RADIO TEXT, which is
additional information on the station and programme
being broadcast.
RADIO TEXT information appears as ‘running’ text
in the display. RADIO TEXT is transmitted character
by the radio station. As a result of that it may take
some time until the entire text has been completely
received.
RDS DISPLAY
When a unit is tuned to an FM station that is
transmitting RDS data, the Front Panel Information
Display will automatically show the station name
or RDS TEXT in place of the typical display of the
station’s broadcast frequency.
To change the display, switch the remote controller to
TUNER mode and press the < / > button until 004 is
displayed. Press the DISPLAY button.
5. After selecting the fi rst character to be entered,
press the MEMORY or ENTER button, or press
the MEMORY button on the remote controller.
The entry in this column is fi xed and the next
column starts to fl ash. Fill the next column the
same way.
To move back and forth between the characters,
press the 1 / 2 cursor buttons on the front panel
or the remote controller.
Note:
• Unused columns should be filled by entering
blanks.
6. To save the name, press the MEMORY or
ENTER button on the front panel, or press the
MEMORY button on the remote controller for
more than 2 seconds.
Instead of using the 3 and 4 cursor buttons
or the on the front panel remote controller to
select characters, characters can be input from
the numeric keys of the remote controller. See
the below table for a correspondence between
characters and numeric keys.
Ten keypad Press, press again, press again, etc.
1 A → B → C → 1 → A
2 D → E → F → 2 → D
3 G → H → I → 3 → G
4 J → K → L → 4 → J
5 M → N → O → 5 → M
6 P → Q → R → 6 → P
7 S → T → U → 7 → S
8 V → W → X → 8 → V
9 Y → Z → space → 9 → Y
0 – → + → / → 0
NAME INPUT OF THE PRESET STATION.
This function allows the name of each preset channel
to be entered using alphanumeric characters.
Before name inputting, you need to store preset
stations with the preset memory operation.
TOP TOP
ZONE ZONE SPEAKER SPEAKER
DISPLAY DISPLAY INPUT INPUT 7.1CH 7.1CH DIRECT DIRECT PURE PURE
PHONES PHONES
THX THX M-DAX M-DAX
MODE MODE SURROUND SURROUND CLEAR CLEAR MEMORY MEMORY T-MODE T-MODE BAND BAND EXIT EXIT MENU MENU ZONE ZONE
DOWN DOWN
VOLUME VOLUME
UP UP
INPUT INPUT SELECTOR SELECTOR
AUTO AUTO
SETUP MIC SETUP MIC
HDMI HDMI
M-DAX M-DAX
PURE DIRECT PURE DIRECT
POWER ON/OFF POWER ON/OFF STANDBY STANDBY
AV PRE TUNER AV8003 AV PRE TUNER AV8003
ENTER ENTER
5. 2. 5. 6. 4.
4.
5.
5.
2.5.6. 2.5.6.
4.
1. Recall the preset number to be inputted name
with the method described in “Recalling” a
preset station.
2. Press the MEMORY button on the front panel
or press the MEMORY button on the remote
controller for more than 3 seconds.
3. The left most column of the station name
indicator fl ashes, indicating the character entry
ready status.
4. When you press the 3 or 4 cursor buttons on
the front panel or the 3 or 4 cursor buttons on
the remote controller, alphabetic and numeric
characters will be displayed in the following
order:
A → B → C ... Z → 1 → 2 → 3 ..... 0 → – → +
→ / → (Blank) → A
UP →
→ DOWN
SORTING PRESET STATIONS
TOP TOP
ZONE ZONE SPEAKER SPEAKER
DISPLAY DISPLAY INPUT INPUT 7.1CH 7.1CH DIRECT DIRECT PURE PURE
PHONES PHONES
THX THX M-DAX M-DAX
MODE MODE SURROUND SURROUND CLEAR CLEAR MEMORY MEMORY T-MODE T-MODE BAND BAND EXIT EXIT MENU MENU ZONE ZONE
DOWN DOWN
VOLUME VOLUME
UP UP
INPUT INPUT SELECTOR SELECTOR
AUTO AUTO
SETUP MIC SETUP MIC
HDMI HDMI
M-DAX M-DAX
PURE DIRECT PURE DIRECT
POWER ON/OFF POWER ON/OFF STANDBY STANDBY
AV PRE TUNER AV8003 AV PRE TUNER AV8003
ENTER ENTER
If you have stations memorized, and there is a gap in
the sequential order:
I.e. the stations are stored as follows
1) 87.1 MHz
2) 93.1 MHz
3) 94.7 MHz
10) 105.9 MHz
(notice there is no stations programmed for pre sets
for 4-9), you can have pre set 10 become pre set 4:
To sort the numbers, press the
4 cursor button while
holding down the MEMORY button.
“PRESET SORT” will appear on the display and
sorting will be done.
AV8003N.indb 50 AV8003N.indb 50 08.4.28 10:49:31 AM 08.4.28 10:49:31 AM