Marantz SR7300N - Manual (Page 19)

16
ENGLISH
IN
RC-5 DC OUT
AUDIO
COMPONENT VIDEO
DIGITAL OUT DIGITAL IN
SBL OUT SL
TV SW VCR1 DVD
SBL C
SR MULTI
SR
L C
R SW SBR
DSS / VCR2
OUT IN
CDR / MD
IN OUT
TAPE
IN OUT
CD
IN OUT
SBR
TV
DVD
OPT
DSS / VCR2
TV DVD
COAX
MULTI MONI IN OUT OUT
S-VIDEO VIDEO
MONI OUT IN DVD VCR1
IN OUT
DSS / VCR2
IN OUT
VCR1 DSS/VCR2
MONI OUT RS-232C
ANTENNA
FM (75 Ω) GND AM
OUT OUT
SERIAL NO.
SL
R
L
7.1CH
IN
PRE
OUT
MODEL NO. SR7300
FRONT A SURROUND
BACK FRONT B CENTER SURROUND
MULTI
RC
OUT
L R L R L R SBL SL
SW
SBL C
SR MULTI
L C
SBR
SL
R
L
PRE
OUT
FRONT A SURROUND
BACK FRONT B CENTER SURROUND
L R L R L R
6 5 4 1 2 3
L
R
Y C B / P B C B / P B C B / P B C R / P R Y C R / P R Y C R / P R
(AUX2)
SPEAKER SYSTEMS
FRONT A OR B, CENTER, SURROUND, SURR. BACK :
MINIMUM 6 OHMS
FRONT A AND B : MINIMUM 8 OHMS
AC IN
AC OUTLET
230V 50HZ
UNSWITCHED
100W MAX
SW
SBL C
SR SBR
SL
R
L
PRE PRE
OUT OUT
FRONT A SURROUND
BACK FRONT B CENTER SURROUND
L R L R L R
OUT
IN
R L
SPEAKER SYSTEMS
A A
B B L
MAX MAX MIN MIN MAX MAX MIN MIN
R
R
L
DIRECT DIRECT INPUT INPUT LEVEL VARIABLE VARIABLE
INPUT INPUT THRU THRU OUTPUT OUTPUT
R
L
REMOTE REMOTE CONTROL CONTROL
INVERT
OUTPUT INPUT
LEVEL BTL REMOTE CONT. EXT. CONT. IN
VIDEO/ +5~13V DC SYSTEM OUT OUT
INPUT
MASTER SLAVE
MIN MAX IN
F U SE
SPEAKER SYSTEM
MINIMUM 4 OHMS
CONNECTING SPEAKERS
CONNECTING SPEAKER WIRE
1.
Strip away approx. 3/8 inch (10 mm) of wire insulation.
2.
Twist the bared wire ends tight to prevent short circuits.
3.
Loosen the knob by turning counterclockwise.
4.
Insert the bare part of the wire into the hole in the side of each
terminal.
5.
Tighten the knob by turning clockwise to secure the wire.
Caution:
• Be sure to use speakers with the specified impedance shown on
the rear panel of this unit.
• To prevent damage to circuitry, do
not let the bare speaker wires touch
each other and do not let them touch
any metal part of this unit.
• Do not touch the speaker terminals
when the power is on. It may cause
electric shocks.
• Do not connect more than one
speaker cable to one speaker terminal. Doing so may damage
this unit.
Note:
• Be sure to connect the positive and negative cables for the
speaker properly. If they are miss-connected, the signal phase
will reversed and the signal quality will be corrupted.
CONNECTING A SUBWOOFER
Use the PRE OUT SUBWOOFER jack to connect a powered
subwoofer (power amplifier built in ).
If your subwoofer is passive type (power amplifier is not built in),
connect a monaural power amplifier to the PRE OUT SUBWOOFER
jack and connect the subwoofer to the amplifier
1. 2.
3. 4. 5.
POWERED
SUBWOOFER
POWER
AMPLIFIER
PASSIVE
SUBWOOFER
FRONT
RIGHT LEFT
SURROUND
SURROUND
BACK
CENTER
or
RIGHT LEFT
SURROUND
BACK
RIGHT LEFT
STEREO
POWER
AMPLIFIER
10 mm