Connecting audio components, Basic connections, English connecting speaker wire – Marantz NR1501 User Manual
Page 13: Connecting digital audio components, Front r/l center surround r/l, Surround back r/l, Names and functions, Loosen the knob by turning it counterclockwise, Push the lever and hold it down, Release the lever
NAMES AND
FUNCTIONS
9
BASIC
CONNECTIONS
BASIC
OPERA
TION
ADV
ANCED
CONNECTIONS
SETUP
ADV
ANCED
OPERA
TION
TROUBLESHOOTING
OTHERS
BASIC
CONNECTIONS
ENGLISH
CONNECTING SPEAKER WIRE
1.
Strip away approx. 10 mm (3/8 inch) of wire
insulation.
2.
Twist the bared wire ends tight, to prevent
short circuits.
1.
2.
10 mm
(3/8 inch)
FRONT R/L
CENTER
SURROUND R/L
3.
Loosen the knob by turning it counterclockwise.
4.
Insert the bare part of the wire into the hole
in side of each terminal.
5.
Tighten the knob by turning it clockwise to
secure the wire.
3.
4.
5.
SURROUND BACK R/L
3.
Push the lever and hold it down.
4.
Insert the twisted ends of the wires into the
hole in the terminal.
5.
Release the lever.
3.
4.
5.
BASIC CONNECTIONS
CONNECTING AUDIO COMPONENTS
The VCR OUT terminals are for recording purposes. The sound of the analog input source component
currently selected is output from these terminals.
The digital sound, which has been input to the DIGITAL IN or HDMI terminal, is not output from the VCR
OUT terminals.
IN
IN
OUT
OUT
PRE OUT
PRE OUT
GAME
GAME
DVD
DVD
DSS
DSS
L
L
R
R
DIGITAL
DIGITAL
AUDIO
AUDIO
IN
IN
SURROUND BACK
SURROUND BACK
R
R
L
L
3
3
2
2
1
1
GND
GND
AM
AM
AC IN
AC IN
MODEL NO. NR1501
MODEL NO. NR1501
VIDEO
VIDEO
FM
FM
((75
75
Ω
Ω))
SPEAKER SYSTEMS : 6-8 OHMS
SPEAKER SYSTEMS : 6-8 OHMS
COMPONENT VIDEO
COMPONENT VIDEO
DVD
DVD
MONITOR OUT
MONITOR OUT
OUT
OUT
MONITOR OUT
MONITOR OUT
IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
OUT
OUT
SUB
SUB
DVD
DVD
DSS
DSS
VCR
VCR
CD
CD
AUX 2
AUX 2
WOOFER
WOOFER
ANTENNA
ANTENNA
REMOTE CONTROL
REMOTE CONTROL
ANALOG AUDIO
ANALOG AUDIO
DSS
DSS
VCR
VCR
IN
IN
IN
IN
DVD
DVD
DSS
DSS
IN
IN
VCR
VCR
P
P
R
R
//C
C
R
R
P
P
R
R
//C
C
R
R
P
P
B
B
//C
C
B
B
P
P
B
B
//C
C
B
B
Y
Y
Y
Y
OUT
OUT
BLU-RAY
BLU-RAY
CENTER
CENTER
R
R -
- SURR.
SURR. -
- L
L
R
R -
- FRONT
FRONT -
- L
L
DIGITAL
DIGITAL
AUDIO
AUDIO
3
3
IN
IN
CD
CD
ANALOG AUDIO
ANALOG AUDIO
R
R
L
L
OUT
L
R
L R
R L
DIGITAL
OUTPUT
L
R
CD Player
Analog Audio
Digital Audio (coaxial)
Notes
• Do not connect this unit and other components to mains power until all connections between components have
been completed.
• Insert all plugs and connectors securely. Incomplete connections may make noise.
• Be sure to connect the left and right channels properly.
Red connectors are for the R (right) channel, and white connectors are for the L (left) channel.
• Be sure to connect input and output properly.
• Refer to the instructions for each component that is connected to this unit.
• Do not bundle the connected cables with the power cord or speaker cables. Doing so may produce noise.
CONNECTING DIGITAL AUDIO
COMPONENTS
• There are 3 digital inputs, 2 coaxial jacks and
1 optical jack, on the rear panel. You can use
these jacks to input PCM, Dolby Digital and DTS
bitstream signals from a CD, DVD, or other digital
source components.
• Refer to the instructions for each component. To
setup the digital audio format of DVD player, or
other digital source’s connected to digital input
jacks.
• Use fiber optical cables (optical) for DIGITAL
AUDIO-1,2 input jacks. Use 75 ohms coaxial
cables (for digital audio or video) for DIGITAL
AUDIO-3 input jacks.
• You can designate the input for each digital input/
output jacks according to your component. (See
page 20)
Note
• The digital signal jacks on this unit conform to
the EIA standard. If you use a cable that does
not conform to this standard, this unit may not
function properly.