Specifications – Denon RCD-CX1 User Manual

Page 27

Get
ting Star

ted

Connections

Set
up

Pla
ybac

k
Set
ting the

Timer

Other F

unctions

oubleshooting

ENGLISH

oubleshooting

Symptom

Cause

Countermeasure

Page

Buzzing noise in
FM broadcasts.

• The antenna cable is not properly

connected.

• Noise interference from a nearby

electronic device equipped with
a microprocessor, or the radio
broadcast signal is weak.

• Connect the antenna properly.

• Reposition the equipment or the

positions or directions of the
connection cables, antenna, etc.

• Connect an outdoor antenna.

–

Hissing or buzzing
noise is heard in
AM broadcasts.

• Noise interference from a

nearby monitor, etc., or there
is interference in the broadcast
signal.

• Turn off the monitor.
• Change the position or direction

of the AM loop antenna.

• Connect an outdoor antenna.

–
–

–

Humming noise
is heard in AM
broadcasts.

• There is interference from current

in power cords.

• Connect an outdoor antenna.

–

TunerH

Symptom

Cause

Countermeasure

Page

When playing
records, a wailing
noise (howling) is
produced when
the volume is
raised.

• The player and speakers are too

close together.

• The floor is soft and vibrates

easily.

• Move the player and speakers as

far apart as possible.

• Use cushions or spikes to absorb

the vibrations of the speakers
being conveyed from the floor.

–

Record PlayerH

Symptom

Cause

Countermeasure

Page

iPod cannot be
played.

• Device you want to play and set

input source do not match.

• Cable is not properly connected.
• Control dock for iPod’s AC

adapter is not connected to
power outlet.

•

Select an appropriate input
source.

• Reconnect.
• Plug the control dock for iPod’s

AC adapter into a power outlet.

9
–

iPodH

Symptom

Cause

Countermeasure

Page

Set does not work
properly when
remote control
unit operated.

• Batteries are worn.
• You are operating outside of the

specified range.

• Obstacle between main unit and

remote control unit.

• The batteries are not inserted in

the proper direction, as indicated
by the polarity marks in the
battery compartment.

• The set’s remote control sensor

is exposed to strong light (direct
sunlight, inverter type fluorescent
bulb light, etc.).

• Replace with new batteries.
• Operate within the specified

range.

• Remove the obstacle.

• Insert the batteries in the

proper direction, following the
polarity marks in the battery
compartment.

• Move the set to a place in which

the remote control sensor will
not be exposed to strong light.

4
4

Remote Control UnitH

Specifications

Receiver section

Rated output:

2-channel driving

37.5 W + 37.5 W (8 Ω/ohms, DIN, 1 kHz, T.H.D. 0.7 %)

75 W + 75 W (4 Ω/ohms, DIN, 1 kHz, T.H.D. 0.7 %)

High frequency distortion:

0.05 % (Rated output: –3 dB), 8 Ω/ohms, 1 kHz

Output terminals:

Speaker 4 ~ 16 Ω/ohms

Suited for headphones/stereo headphones

Equalizer amplifier output
(REC OUT terminals):

Rated output : 150 mV

Input sensitivity / Input impedance:

PHONO (MM)

: 2.5 mV / 47 kΩ/kohms

PHONO (MC)

: 0.2 mV / 100 Ω/ohms

CD, LINE1, LINE2 : 130 mV / 47 kΩ/kohms

RIAA deviation:

PHONO (MM) : 20 Hz ~ 20 kHz ±0.5 dB

PHONO (MC) : 30 Hz ~ 20 kHz ±0.5 dB

Reception frequency range:

FM : 87.5 MHz ~ 107.9 MHz

AM : 520 kHz ~ 1710 kHz

Reception sensitivity:

FM : 1.5 μV / 75 Ω/ohms

AM : 20 μV

FM channel separation:

35 dB (1 kHz)

FM S/N ratio:

Monaural : 74 dB

Stereo : 70 dB

FM harmonic distortion:

Monaural : 0.3 %

Stereo : 0.4 %

S/N ratio:

PHONO (MM) : 84 dB

(With input terminals short-circuited, 5 mV input signal)

PHONO (MC) : 70 dB

(With input terminals short-circuited, 0.5 mV input signal)

(A-weighted network):

LINE1, LINE2 : 95 dB (input terminals short-circuited)

Tone control:

BASS

: 100 Hz ± 8 dB

TREBLE : 10 kHz ± 8 dB

Frequency response:

10 Hz ~ 40 kHz (+0.5 dB, –3 dB) (INPUT: LINE1, PURE DIRECT: ON)

Clock/Timer section

Clock type:

Power line frequency synchronized method (Within ±60 seconds per month)

Timer:

Everyday timer / Once timer : One system each

Sleep timer : Max. 90 minutes

CD section

[Super Audio CD]

[CD]

• Analog output
Signal type:

1-bit DSD

16-bit linear PCM

Sampling frequency:

2.822 MHz

44.1 kHz

Usable discs:

Super Audio CD

Compact Disc

• Digital output
Optical:

–

–15 ~ –21 dBm

Emission wavelength:

–

660 nm

General

Power supply:

AC 120 V, 60 Hz

Power consumption:

50 W

0.3 W (Standby)

Maximum external dimensions:

300 (W) x 110 (H) x 341 (D) mm

Weight:

8.0 kg

Remote control unit (RC-1109)

Remote control method:

Infrared pulse method

Batteries:

R03/AAA Type (two batteries)

Maximum external dimensions:

44 (W) x 233 (H) x 22 (D) mm

Weight:

165 g (including batteries)

For purposes of improvement, specifications and design are subject to change without notice.

Specifications

1.RCD-CX1E3_ENG.indd 24

2008/06/30 11:12:56