Greenheck Maxitrol Series 14 - Manual

SERIES 14 INSTALLATION INSTRUCTIONS
and field service check list
Page 2 Introduction and Dimensions
Page 3 Specifications
Installation of Components
Page 4 & 5 Field Service Checklist
Page 6 Preliminary Circuit Analysis
Low Fire Start Time Adjustment
Sensitivity Adjustment
Page 7 Wiring Diagrams
Page 8 Temperature Calibration
Valve Adjustments
Table of Contents
A1014L1 Amplifier /
AD1014/AD1014L1
Amplifier-Selectors
A1014 Amplifier
System Components
TS114G (90° to 140° F)
TS114J (110° to 160° F) To be used w/ AD1014-1116
TS214__ (dual sensor - any combination of 2 standard ranges available)
Example - TS214G (55° to 90° F and 90° to 140° F, use w/TD114 & TD114G,
or TD214G [selector w/switch], or AD1214G)
Example - TS214AD (80° to 130° F and 200° to 250° F, use w/TD114A &
TD114D, or TD214AD [selector w/ switch], or AD1214AD)
Mixing Tubes: use with Sensors
MT1-9 or 2-9 (9" length)
MT1-12 or 2-12 (12" length)
MT1-23 or 2-23 (23" length)
MT1-28 or 2-28 (28" length)
MT1-57 (57" length)
Valves:
M411 (3/8" & 1/2" pipe size)
M511 (1/2" & 3/4" pipe size)
M611 (3/4" & 1" pipe size)
MR212D (1", 1-1/4", 1-1/2" pipe size)
MR212E (1-1/2" & 2" pipe size)
MR212G (2-1/2" & 3" pipe size)
MR212J (4" flanged)
MR212-2D, E, G, J (same as above except used for 2-speed blower or dual fuel
operation)
NOTE: M (Modulator) valve requires a pressure regulator for high fire setting. MR
(Modulator-Regulator) valve requires no pressure regulator up to 5 psi.
Optional:
Dual Temperature Selector:
DOOR HEATERS -
TD114HD use w/TS114 (door closed 55° to 90° F/open 90° to 140° F)
PAINT SPRAY BOOTHS OR OTHER DUAL APPLICATIONS-
TD214__ (dual selector w/switch - any comb. of 2 standard ranges avail.)
Example - TD214G (55° to 90° F [spray] and 90° to 140° F [dry], use w/TS214G
Example - TD214AD (80° to 130° F and 200° to 250° F, use w/TS214AD
TD214__X (same as TD214__, less enclosure)
Inlet Air Temperature Sensors: use with Mixing Tube
TS10765A (8:1 ratio)
TS10765B (5:1 ratio)
TS10765C (3.5:1 ratio)
Override Stat: (use only with TD114, F ,-1, A-1)
T115 (40° to 90° F)
Valves
Remote Temperature Selector
Override Stat
Amplifiers:
A1014 (use with all temperature ranges)
A1014L1 (all ranges - adjustable low fire start duration)
Amplifier-Selectors: (with integral temperature dial)
AD1014-4080 (40° to 80° F)
AD1014-5590 (55° to 90° F)
AD1014-1116 (110° to 160° F)
AD1014-1621 (160° to 210 ° F)
AD1014L1-4080 (40° to 80° F - adjustable low fire start duration)
AD1014L1-5590 (55° to 90° F - adjustable low fire start duration)
AD1014L1-1116 (110° to 160° F - adjustable low fire start duration)
AD1014L1-1621 (160° to 210° F - adjustable low fire start duration)
Dual Temperature Amplifier-Selectors:
AD1214__ (integral dual selector - any comb. of 2 standard ranges avail.)
Example - AD1214BC (120° to 170° F and 160° to 210° F, use w/TS214BC
Example - AD1214AD (80° to 130° F and 200° to 250° F, use w/TS214AD
Remote Temperature Selectors:
TD114 (55° to 90° F w/override 0° to 40° over set point)
TD114A (80° to 130° F)
TD114A-1 (80° to 130° F w/ override 0° to 40° F over set point)
TD114B (120 to 170° F)
TD114C (160° to 210° F)
TD114D (200° to 250° F)
TD114E (100° to 250° F)
TD114F (40° to 80° F w/override 0° to 40° over set point)
TD114G (90° to 140° F)
TD114-1 (55° to 90° F w/120° to 170° F override) * use w/TS114
TD114-2 (55° to 90° F w/two outputs)
TD114G-2 (90° to 140° F w/two outputs)
NOTE: Remote Selector and Discharge Temperature Sensor must have same
temperature range to be compatible.
Optional: ETD-1 enclosure, EFP-1 cover plate only - no enclosure
Discharge Air Temperature Sensors: use with Mixing Tube
TS114 (55° to 90° F)
TS114A (80° to 130° F)
TS114B (120° to 170° F)
TS114C (160° to 210° F)
TS114D (200° to 250° F)
TS114E (100° to 250° F)
TS114F (40° to 80° F)
Mixing Tube and Sensor
AD1214 Amplifier
©2007 Maxitrol Company, All Rights Reserved 1