Types of isolation – Greenheck Isolation Assembly Instructions (468646) User Manual
Page 4
4
®
®
There are several types of bases available for use with centrifugal/industrial process fans. Table 1 shows
available uses for specific sizes and styles of fans.
Types of Isolation
Table 1
Arrangement
Fan Type
Direct Mount
Structural Base
Inertia Base
1
AF/BISW
No
Yes
Yes
IPA*
3
AF/BISW
No
Yes
Yes
AF/BIDW
4, 8
IPA*
Consult Factory
Yes
Yes
AF/BISW
Yes
9
AF/BISW 7-36
Consult Factory
Yes
Yes
IPA 5-19*
AF/BISW 40-73
Consult Factory
Yes
Yes
IPA 21-41*
10
AF/BISW 7-36
Yes
Yes
Yes
AF/BISW 40-73
Consult Factory
IPA 5-19*
Yes
Structural Base — Consult Factory on DB, BAD or TAD discharges.
Inertia Base — Not available on DB, BAD or TAD discharges.
*Consult Factory for isolation options for material handling fans (IPW/IPO)
Below are photos of the isolation types offered: Direct Mount [no structural base], Structural Base, and Inertia
Base. Bases can be supplied with or without isolators. Contact a Greenheck representative for additional
information on each type of base and their advantages.
Structural Base or
Concrete Filled Inertia Base
with Free Standing Spring Isolators
Direct Mount
with Neoprene Isolators
- VCD-40 Extension Pin Kit 316SS (475290) (2 pages)
- 331-2856, 332-2856 - Siemens 6 Actuator (454206) (2 pages)
- 331-2976, 332-2976 - Siemens 4 Actuator (454202) (2 pages)
- 331-4551, 332-4551 - Siemens 3 Actuator (454201) (2 pages)
- Adjustable Pressure Controller (468292) (3 pages)
- 7800 Series Relay Modules (12 pages)
- Standard Control - MSSC (476372) (4 pages)
- NFB Series Actuators External Mount (464236 IOM) (2 pages)
- GND Series External Mount (473723) (4 pages)
- Amplifier for 7800 Series Relay Module (8 pages)
- APEX Curbs (462831) (4 pages)
- AMD-xx-TD Transmitter (35 pages)
- Blade Seal Repalcement (HCDR Series) (1 page)
- VCD (463384) (12 pages)
- BAPI Zone Pressure Touch (ZPT) Sensor (6 pages)
- VCD (463384) (10 pages)
- Blade Seal Replacement (HCD Series) (2 pages)
- BR Series - Counterweight Adjustment (469420) (4 pages)
- Leakage Rated Ceiling Radiation Dampers (475063 IOM). (32 pages)
- Canopy Hoods (452413 IOM) (36 pages)
- Clean-Out Port Kit (472428) (1 page)
- Centrifugal (CSW, BIDW, AFDW), Industrial (IPA, IPO, IPW) and Filtered Supply (LSF) (463687) (12 pages)
- Close Indicator Switch for Fire Dampers (474050) (1 page)
- Concrete Floor with Steel Deck Supplement (463562) (1 page)
- CRD-3XX and CRD-7XX Series for SP fans (452832) (2 pages)
- VCD (463384) (8 pages)
- VCD (463384) (4 pages)
- Single Side Retaining Angle (52 pages)
- DG / DGX with Pilot Ignition (463555 IOM) (Pre-2008) (48 pages)
- DG / DGX with Direct Spark (470652) (40 pages)
- Digital Temperature Interlock (474750 IOM) (Pre November 2012) (8 pages)
- DGK (468695) (20 pages)
- DG / DGX with Pilot Ignition (463555 IOM) (Pre-2008) (52 pages)
- Double Gland Axle Seal Replacement (1 page)
- Dock Arm Kit (475367) (4 pages)
- Duct Heaters Series IDHB and IDHC (478052) (8 pages)
- EHH-601D, Channel Installation (474643) (10 pages)
- EHH-601D, Channel Installation with VCD-40 Damper (474644) (8 pages)
- EHH-601D, Flange/Sleeve Installation (474641) (8 pages)
- GM Series (468391) (4 pages)
- EHH-601D, Flange/Sleeve Installation with VCD-40 Damper (474642) (8 pages)
- El-O-Matic E and P Series (12 pages)
- Energy Recovery Filter Hood System (8 pages)
- ERV-582/120 Curbs (460988) (4 pages)
- ESD-635D, Chanel Installation (474639) (10 pages)