Leaning, Djusting, Emperature – Dacor Wall Ovens User Manual

Page 15: Eplacing, Ight

WarnInGs:

are

and

leanInG

selF-CleanInG tIps:

1. if any soil remains in the oven after completion of a Self-cleaning

cycle, repeat the cycle if desired. increase the cleaning time during

future cycles.

. clean the oven regularly to prevent excessive soil build-up. this will

increase the efficiency of the Self-clean cycle and reduce the amount

of smoke and odors generated.

3. Self-clean in the cooler evening hours after cooking is complete and

when electricity rates are lower.

4. in the double oven, if one oven is in the Self-clean mode the other

oven is inoperable.

djUsTInG

The

ven

emperaTUre

Important:

the user may find the temperature in their new oven to be different

from that of their previously-owned appliance. Familiarity with the

old appliance sometimes makes it difficult to get used to a new oven.

If you feel that the oven temperature is consistently high or low, the

temperature of the new oven can be adjusted. the adjustment needs

to be done only once.

the oven temperature may be adjusted (calibrated) by

following these steps:

1. Press “Bake” selector pad.

2. Press the “TIME•TEMP” “+” pad to set a temperature of 500˚F or

higher.

3. Press and hold the “Bake” selector pad. after approximately 5

seconds the temperature display is replaced by “00”. the “Bake”

pad can now be released. the calibration mode has been accessed.

4. Press the “tiMe•teMP” “+“ or “–” pad to set the amount of

temperature adjustment. the temperature can be changed a

maximum of 35˚F higher or lower. Set the adjustment to positive (+)

numbers to increase the oven temperature; set the adjustment to

negative (–) numbers to reduce the oven temperature. temperatures

can be adjusted in increments of 5˚F.

5. after setting the desired temperature adjustment, press the

“caNceL•SecuRe” pad to exit the calibration mode and to reset the

clock display.

Clock Display When Adjusting (Calibrating) the Oven

Temperature

to replace a light bulb, follow these steps:

1. turn off the power at the main power supply.

. Remove the lens cover from the housing by pulling straight out.

note:

In some cases the lens cover may be tight enough to require the

use of your light lens pry stick. this prying tool should be used with

caution. Do not cause uneven stress on the lens cover. Gently insert

the point end of the pry stick under the center edge of the lens cover

on the side facing the oven door. hold your hand under the lens for

support then pry out to remove the lens cover.

3. Pull the light bulb out and replace it with a special 10-watt halogen

bulb rated for use in a Self-cleaning oven. use dacoR® Part No.

86364 available from any authorized dacoR® parts distributor or

dealer.

4. Reinstall the lens cover by aligning the cover over the opening and

gently pressing it into its original position.

5. turn the power back on at the main power supply.

Clock Display in Self-Cleaning Mode

notes:

1. If “CanCel•seCure” is not pressed after setting the

adjustment, the clock display will automatically reset in 6

seconds.

2. the amount of temperature adjustment may be changed again

by repeating the calibration procedure. the oven will only retain

the amount of the most recent temperature adjustment.

3. the temperature adjustment is not affected by an electrical

power failure

4. the temperature adjustment only affects standard Bake and

Convection Bake modes. Broil and self-Clean temperatures

cannot be adjusted.

the light assembly consists of a removable lens cover and 10-

watt 1vac halogen bulb, as well as a light fixture housing. Light

bulb replacement is considered to be a homeowner maintenance

operation.

to prevent electrical shock and/or personal injury:

1. make certain that the appliance and light bulb are cool and that

power to the appliance has been turned off before replacing the

light bulb.

2. always ensure that the lens cover is in place when using the

appliance. the lens cover protects the bulb from reakage

caused by high temperatures or mechanical shock.

eplaCInG

The

ven

IGhT

Lens Cover

Oven Light Assembly

Important:

With the oven at room temperature, if the self-Clean mode is

accidentally selected and the oven enters self-Clean mode (indicated

by “loCK” and “on” in the clock display), the user must cancel out

of this mode before attempting to select a different mode. to cancel,

press the “CanCel•seCure” pad. Wait at least 60 seconds before

attempting to select another mode. this allows the door latch time

to unlock.