Flowserve MT Bevel Gearboxes IOM - Manual (Page 19)

19
Limitorque MT Series FCD LMENIM4201-00 – 06/10
flowserve.com
FLOWSERVE-LIMITORQUE
SCALE ORDER NO.
DWG. NO.
SHEET
1 OF 1
REV.
TITLE
THIS DOCUMENT CONTAINS INFORMATION WHICH LIMITORQUE DEEMS CONFIDENTIAL
AND PROPRIETARY, THEREFORE, IT IS NOT TO BE USED, DUPLICATED, OR
DISCLOSED, IN WHOLE OR IN PART, WITHOUT THE WRITTEN CONSENT OF LIMITORQUE
CASTING AND OTHER DIMENSIONAL TOLERANCE
LIMITS ARE PER LIMITORQUE ENGINEERING DESIGN
STANDARDS (EDS).
MATERIAL
5114 WOODALL ROAD, LYNCHBURG, VIRGINIA 24506-1318
PROPRIETARY NOTICE
REVISIONS
REV. DESCRIPTION
DA
TE
BY APPVD GENERAL C/N
B
SIZE
DRAWN
CHECKED
APPROVED
DATE
DATE
DATE
1. ALL DIMENSIONS ARE IN INCHES.
2. REMOVE ALL BURRS AND SHARP CORNERS
3. MACHINED SURFACE FINISH TO BE 250
MICROINCHES.
4.FILLET RADII MAY BE TURNED UP TO .020
BELOW THE FINISH DIAMETER.
5. DIMENSIONS IN PARENTHESIS (X..XXX) ARE
FOR REFERENCE ONLY.
6. DIMENSIONS IN BRACKETS [X.XXX] ARE FOR
MANUFACTURING DATA ONLY.
7. ALL VIEWS ARE THIRD ANGLE PROJECTIONS.
8. DIMENSIONING, TOLERANCING, SYMBOLS,
THREADS, ETC. ARE PER LIMITORQUE
ENGINEERING DESIGN STANDARDS (EDS)
GENERAL MANUFACTURING NOTES UNLESS
OTHERWISE SPECIFIED:
L1065 12/15/93 CF-RGP
TOLERANCE LIMITS UNLESS OTHERWISE SPECIFIED:
MACHINED DIMENSIONS:
.X =±.04
.XX =±.02
.XXX =±.010
ANGLES = ± 5°
FILLET RADII = ±.015 ( > .031 )
= ±.007 ( < .031 )
DEFAULT FILLET RADII = .015/.039
CHAMFERS = ±.02
TAP DEPTHS ARE MINIMUM
KDC 5/17/05
UNIT ASSEMBLY, MT-3
1:2
01-602-0992-2 B
KR 11/11/05
KGR 11/11/05
A ADD PIECE #26,27,28,29,30,31,33,62 TO AGREE W/BOM BB
9-9
2009
23900-1022
NA KDC
2-17
-10 NA ADD PIECE #32 TO AGREE W/BOM B KDC
7
1
4
6
4
3
2
10 11
13
12
8
22
17
19
18
21
20
25
29 33
27
62
16
28
9
26
31 30
32
23 24
14
15
16
Figure 6.3 – MT-3 Parts Diagram
Piece Quantity Description
1 1 Thrust Base
2 53 Ball Bearing
3 1 Bevel Gear
4 1 Bevel Housing
5 2 Radial Ball Bearing
6 2 Spacer
7 1 Input Pinion
8 1 Retaining Ring
9 1 Motorized Adapter
10 1 Stem Nut
11 1 Thrust Ring
12 2 Needle Bearings
13 4 Raceway Washer
14 8 Hex HD Cap Screw
15 7 Lockwasher
16 3 O-Ring
17 3 Relief Fitting
Piece Quantity Description
18 1 Lip Seal
19 1 Flat Head Screw
20 1 Lockwasher
21 1 Stat-O-Seal Washer
22 1 O-Ring
23 4 Hex HD Cap Screw
24 4 Lockwasher
25 1 Stat-O-Seal Washer
26 1 Key
27 1 Flat Washer
28 4 Pipe Plug
29 2 Drive Screw
30 1 Shim
31 1 Shim
32 1 Spacer Ring
33 1 Nameplate
62 1 Gasket
Table 6.3– MT-3 Parts List