Flowserve MT Bevel Gearboxes IOM - Manual (Page 17)

17
Limitorque MT Series FCD LMENIM4201-00 – 06/10
flowserve.com
BASE VIEW A
FLOWSERVE-LIMITORQUE
SCALE ORDER NO.
DWG. NO.
SHEET
1 OF 1
REV.
TITLE
THIS DOCUMENT CONTAINS INFORMATION WHICH LIMITORQUE DEEMS CONFIDENTIAL
AND PROPRIETARY, THEREFORE, IT IS NOT TO BE USED, DUPLICATED, OR
DISCLOSED, IN WHOLE OR IN PART, WITHOUT THE WRITTEN CONSENT OF LIMITORQUE
CASTING AND OTHER DIMENSIONAL TOLERANCE
LIMITS ARE PER LIMITORQUE ENGINEERING DESIGN
STANDARDS (EDS).
MATERIAL
5114 WOODALL ROAD, LYNCHBURG, VIRGINIA 24506-1318
PROPRIETARY NOTICE
REVISIONS
REV. DESCRIPTION DA
TE
BY
APPVD GENERAL C/N
B
SIZE
DRAWN
CHECKED
APPROVED
DATE
DATE
DATE
1. ALL DIMENSIONS ARE IN INCHES.
2. REMOVE ALL BURRS AND SHARP CORNERS
3. MACHINED SURFACE FINISH TO BE 250
MICROINCHES.
4.FILLET RADII MAY BE TURNED UP TO .020
BELOW THE FINISH DIAMETER.
5. DIMENSIONS IN PARENTHESIS (X..XXX) ARE
FOR REFERENCE ONLY.
6. DIMENSIONS IN BRACKETS [X.XXX] ARE FOR
MANUFACTURING DATA ONLY.
7. ALL VIEWS ARE THIRD ANGLE PROJECTIONS.
8. DIMENSIONING, TOLERANCING, SYMBOLS,
THREADS, ETC. ARE PER LIMITORQUE
ENGINEERING DESIGN STANDARDS (EDS)
GENERAL MANUFACTURING NOTES UNLESS
OTHERWISE SPECIFIED:
L1065 12/15/93 CF-RGP
TOLERANCE LIMITS UNLESS OTHERWISE SPECIFIED:
MACHINED DIMENSIONS:
.X =±.04
.XX =±.02
.XXX =±.010
ANGLES = ±5°
FILLET RADII = ±.015 ( > .031 )
= ±.007 ( < .031 )
DEFAULT FILLET RADII = .015/.039
CHAMFERS = ±.02
TAP DEPTHS ARE MINIMUM
UNIT ASSEMBLY,
MT-2
KDC 5/31/05
01-602-0993-2
1:2
BB 5/31/05
BB 5/31/05
A CORRECTED BALLOON NOS. AND PART NO. FOR ITEM 23 BB 12/7
2007
B
KDC NA
6/1
2009
BB ADD ADDITIONAL GREASE FITTING & RELIEF VIEW A
PC#14, 15, 16, 19, 26 NAMEPLATE & ALIGN BALLOONS WITH B320'S
NA B
23900-1025
1
2
3
8
14
19
5
21
9 61
7
6
11
23
22
29
24
4
12 13
27 28
14
11
10
20
17
18
60
15
19
14 26
16
62
BASE VIEW A
FLOWSERVE-LIMITORQUE
SCALE ORDER NO.
DWG. NO.
SHEET
1 OF 1
REV.
TITLE
THIS DOCUMENT CONTAINS INFORMATION WHICH LIMITORQUE DEEMS CONFIDENTIAL
AND PROPRIETARY, THEREFORE, IT IS NOT TO BE USED, DUPLICATED, OR
DISCLOSED, IN WHOLE OR IN PART, WITHOUT THE WRITTEN CONSENT OF LIMITORQUE
CASTING AND OTHER DIMENSIONAL TOLERANCE
LIMITS ARE PER LIMITORQUE ENGINEERING DESIGN
STANDARDS (EDS).
MATERIAL
5114 WOODALL ROAD, LYNCHBURG, VIRGINIA 24506-1318
PROPRIETARY NOTICE
REVISIONS
REV. DESCRIPTION DA
TE
BY
APPVD GENERAL C/N
B
SIZE
DRAWN
CHECKED
APPROVED
DATE
DATE
DATE
1. ALL DIMENSIONS ARE IN INCHES.
2. REMOVE ALL BURRS AND SHARP CORNERS
3. MACHINED SURFACE FINISH TO BE 250
MICROINCHES.
4.FILLET RADII MAY BE TURNED UP TO .020
BELOW THE FINISH DIAMETER.
5. DIMENSIONS IN PARENTHESIS (X..XXX) ARE
FOR REFERENCE ONLY.
6. DIMENSIONS IN BRACKETS [X.XXX] ARE FOR
MANUFACTURING DATA ONLY.
7. ALL VIEWS ARE THIRD ANGLE PROJECTIONS.
8. DIMENSIONING, TOLERANCING, SYMBOLS,
THREADS, ETC. ARE PER LIMITORQUE
ENGINEERING DESIGN STANDARDS (EDS)
GENERAL MANUFACTURING NOTES UNLESS
OTHERWISE SPECIFIED:
L1065 12/15/93 CF-RGP
TOLERANCE LIMITS UNLESS OTHERWISE SPECIFIED:
MACHINED DIMENSIONS:
.X =±.04
.XX =±.02
.XXX =±.010
ANGLES = ±5°
FILLET RADII = ±.015 ( > .031 )
= ±.007 ( < .031 )
DEFAULT FILLET RADII = .015/.039
CHAMFERS = ±.02
TAP DEPTHS ARE MINIMUM
UNIT ASSEMBLY,
MT-2
KDC 5/31/05
01-602-0993-2
1:2
BB 5/31/05
BB 5/31/05
A CORRECTED BALLOON NOS. AND PART NO. FOR ITEM 23 BB 12/7
2007
B
KDC NA
6/1
2009
BB ADD ADDITIONAL GREASE FITTING & RELIEF VIEW A
PC#14, 15, 16, 19, 26 NAMEPLATE & ALIGN BALLOONS WITH B320'S
NA B
23900-1025
1
2
3
8
14
19
5
21
9 61
7
6
11
23
22
29
24
4
12 13
27 28
14
11
10
20
17
18
60
15
19
14 26
16
62
Figure 6.2 – MT-2 Parts Diagram, Base View
Piece Quantity Description
1 1 Bevel Housing
2 1 Thrust Housing
3 1 Bevel Gear
4 1 Stem Nut
5 1 Thrust Ring
6 2 Needle Bearings
7 4 Raceway Washer
8 57 Ball Bearing
9, 10 2 O-ring
11 2 O-ring
12 8 Lockwasher
13 8 Hex Head Cap Screw
14 3 Grease Fitting
15 1 Flat Washer
16 1 CSK Socket Set Screw
Piece Quantity Description
17 1 Nameplate (Blank)
18 2 Drive Screw
19 2 Relief Fitting
20 1 End Cover/ Motorized Adapter
21 1 Input Pinion
22 2 Spacer
23 3 Radial Ball Bearing
24 1 O-Ring
25 1 Shim
26 1 Key
27 4 Lockwasher
28 4 Hex HD Cap Screw
29 1 Retaining Ring
60 1 Transit Plug
61 1 O-Ring
62 1 Gasket
63 1 Pipe Plug
Table 6.2– MT-2 Parts List