Flowserve Casing Blind Covers Metallic - Manual (Page 7)

CASING BLIND COVER USER INSTRUCTIONS ENGLISH 75663450 04-10
Page 7 of 13
3.3 Performance and operation limits 3.3.1 Alloy cross reference chart
Figure 3-2 is the Alloy cross-reference chart for
Flowserve ASME (ANSI) pumps.
This product has been selected to meet the
specification of your purchase order. See section 1.5.
Figure 3-3 is the Alloy cross reference chart for
wrought casing blind covers.
The following data is included as additional information
to help with your installation. It is typical, and factors
such as liquid being pumped, temperature, material of
construction, and seal type may influence this data. If
required, a definitive statement for your application can
be obtained from Flowserve.
3.3.2 Pressure-temperature ratings
The pressure–temperature (P-T) ratings for blind
covers are shown in figure 3-4. Determine the
appropriate cover “Material Group No.” in Figure 3-2.
Interpolation may be used to find the pressure rating
for a specific temperature.
The following provides pressure-
temperature ratings for the blind covers only.
The lowest rating of all parts connected to the
casing must be used. Consult the user
instructions provided with the pump.
Example:
The pressure temperature rating for a Mark 3 GP2
blind cover, 316 construction, with an operating
temperature of 149˚C is found as follows:
a) From Figure 3-2, the correct material group is 2.2
Cover plate material compatibility is
the responsibility of the end user.
b) From Figure 3-4C, the pressure-temperature
rating is 21.5 bar.
Figure 3-2: Casing Blind Cover Alloy cross-reference chart
Flowserve
Material Code
Generic
Designation
Specifications Material Group No.
D3041 316 Plate A240 Type 316 (UNS Designation S31600) 2.2
D3134 Steel Plate A515 Gr. 70 (Gr. 485 - S.I. units) 1.1
Figure 3-3: Casing Cast Alloy cross-reference chart
Flowserve
Material Code
Generic
Designation
Durco Legacy
Codes
ASTM
Specifications
Material
Group No.
E3020 Ductile iron DCI A395, Gr. 60-40-18 1.0
E3033 High chrome iron CR28 A532 class 3 Cr
E4027 High chrome iron CR29 None Cr
E4028 High chrome iron CR35 None Cr
C3009 Carbon steel DS A216 Gr. WCB 1.1
C3062 304 D2 A744, Gr. CF8 2.1
C3069 304L D2L A744, Gr. CF3 2.1
C3063 316 D4 A744, Gr. CF8M 2.2
C3067 316L D4L A744, Gr. CF3M 2.2
C3107 Duplex Stainless CD4M A995, Gr. CD4MCuN 2.8
C4028 Alloy 20 D20 A744, Gr. CN7M 3.17
C4029 Durcomet 5 DV None 2.2
K3005 Inconel 600 DINC A494, Gr. CY40 3.5
K3007 Monel 400 DMM A494, Gr. M35-1 3.4
K3008 Nickel DNI A494, Gr. CZ100 3.2
K4007 Hastelloy B
DC2 A494, Gr. N7M 3.7
K4008 Hastelloy C
DC3 A494, Gr. CW6M 3.8
E3041 Duriron D A518, Gr. 1 No load
E3042 Durichlor 51 D51 A518, Gr. 2 No load
E4035 Superchlor SD51 A518, Gr. 2 No load
D4036 Durco DC8 DC8 None -
H3004 Titanium Ti B367, Gr. C3 Ti
H3005 Titanium-Pd TiP B367, Gr. C8A Ti
H3007 Zirconium Zr B752, Gr. 702C Ti
Duriron, Durichlor 51 and Superchlor are registered trademarks of Flowserve Corporation.
Hastelloy is a registered trademark of Haynes International, Inc.
Inconel and Monel are registered trademarks of International Nickel Co. Inc.