DFI CD9A3 series - Manual (Page 20)

www.dfi .com Chapter 3 Hardware Installation
20
Chapter 3
ȟ
ȟ
ȟ
ȟ
Signal Pin# Pin Type Pwr Rail /Tolerance CD9A3 Series Carrier Board Description
Power and System Management Signals Descriptions
ȟ
ȟ
ȟ
ȟ
SUS_S4# A18 O CMOS 3.3V Suspend/3.3V Indicates system is in Suspend to Disk state. Active low output.
SUS_S5# A24 O CMOS 3.3V Suspend/3.3V Indicates system is in Soft Off state.
WAKE0# B66 I CMOS 3.3V Suspend/3.3V PU 10K to 3.3VSB PCI Express wake up signal.
WAKE1# B67 I CMOS 3.3V Suspend/3.3V PU 10K to 3.3VSB
General purpose wake up signal. May be used to implement wake-up
on PS2 keyboard or mouse activity.
BATLOW# A27 I CMOS 3.3V Suspend/ 3.3V PU 10K to 3.3VSB
Indicates that external battery is low.
This port provides a battery-low signal to the Module for orderly
transitioning to power saving or power cut-off ACPI modes.
LID# A103 I OD CMOS 3.3V Suspend/12V PU 10K to 3.3VSB LID switch. Low active signal used by the ACPI operating system for a LID switch.
SLEEP# B103 I OD CMOS 3.3V Suspend/12V PU 10K to 3.3VSB
Sleep button. Low active signal used by the ACPI operating system to bring the
system to sleep state or to wake it up again.
THRM# B35 I CMOS 3.3V / 3.3V PU 10K to 3.3V Input from off-Module temp sensor indicating an over-temp situation.
THRMTRIP# A35 O CMOS 3.3V / 3.3V PU 10K to 3.3V Active low output indicating that the CPU has entered thermal shutdown.
SMB_CK B13 I/O OD CMOS 3.3V Suspend/3.3V PU 2.2K to 3.3VSB System Management Bus bidirectional clock line.
SMB_DAT B14 I/O OD CMOS 3.3V Suspend/3.3V PU 2.2K to 3.3VSB System Management Bus bidirectional data line.
SMB_ALERT# B15 I CMOS 3.3V Suspend/3.3V
System Management Bus Alert – active low input can be used to
generate an SMI# (System Management Interrupt) or to wake the system.
Signal Pin# Pin Type Pwr Rail /Tolerance CD9A3 Series Carrier Board Description
GPO0 A93
GPO1 B54
GPO2 B57
GPO3 B63
GPI0 A54 PU 100K to 3.3V
GPI1 A63 PU 100K to 3.3V
GPI2 A67 PU 100K to 3.3V
GPI3 A85 PU 100K to 3.3V
Signal Pin# Pin Type Pwr Rail /Tolerance CD9A3 Series Carrier Board Description
VCC_12V
A104~A109
B104~B109
Power 4.75V – 20.0V 4.75V – 20.0V
Primary power input: +12V nominal. All available VCC_12V pins on the connector(s) shall be used.
The module supplies a wide range of power from 4.75V to 20.0V.
VCC_5V_SBY B84~B87 Power 4.75V - 5.25V 4.75V - 5.25V
Standby power input: +5.0V nominal. If VCC5_SBY is used, all
available VCC_5V_SBY pins on the connector(s) shall be used. Only
used for standby and suspend functions. May be left unconnected if
these functions are not used in the system design.
VCC_RTC A47 Power 2.0V - 3.3V 2.0V - 3.3V Real-time clock circuit-power input. Nominally +3.0V.
GND
A1, A11, A21, A31, A41,
A51, A57, A60, A66, A70,
A80, A90, A100, A110, B1,
B11, B21 ,B31, B41, B51,
B60, B70, B80, B90, B100,
B110
Power
Ground - DC power and signal and AC signal return path.
All available GND connector pins shall be used and tied to Carrier
Board GND plane.
Power and GND Signal Descriptions
I CMOS PU 100K to 3V3 General purpose input pins.
GPIO Signals Descriptions
O CMOS 3.3V / 3.3V General purpose output pins.