DFI CD9A3 series - Manual (Page 16)

www.dfi .com Chapter 3 Hardware Installation
16
Chapter 3
COM Express Connectors Signal Description
Signal Pin# Pin Type Pwr Rail /Tolerance CD9A3 Series Carrier Board Description
AC/HAD_RST# A30 O CMOS 3.3V Suspend/3.3V Connect to CODEC pin 11 RESET# Reset output to CODEC, active low.
AC/HDA_SYNC A29 O CMOS 3.3V/3.3V Connect to CODEC pin 10 SYNC Sample-synchronization signal to the CODEC(s).
AC/HDA_BITCLK A32 I/O CMOS 3.3V/3.3V Connect to CODEC pin 6 BIT_CLK Serial data clock generated by the external CODEC(s).
AC/HDA_SDOUT A33 O CMOS 3.3V/3.3V Connect to CODEC pin 5 SDATA_OUT Serial TDM data output to the CODEC.
AC/HDA_SDIN2 B28 I/O CMOS 3.3V Suspend/3.3V Connect 33 ƻ in series to CODEC2 pin 8 SDATA_IN
AC/HDA_SDIN1 B29 I/O CMOS 3.3V Suspend/3.3V Connect 33 ƻ in series to CODEC1 pin 8 SDATA_IN
AC/HDA_SDIN0 B30 I/O CMOS 3.3V Suspend/3.3V Connect 33 ƻ in series to CODEC0 pin 8 SDATA_IN
Signal Pin# Pin Type Pwr Rail /Tolerance CD9A3 Series Carrier Board Description
GBE0_MDI0+ A13 I/O Analog 3.3V max Suspend
GBE0_MDI0- A12 I/O Analog 3.3V max Suspend
GBE0_MDI1+ A10 I/O Analog 3.3V max Suspend
GBE0_MDI1- A9 I/O Analog 3.3V max Suspend
GBE0_MDI2+ A7 I/O Analog 3.3V max Suspend
GBE0_MDI2- A6 I/O Analog 3.3V max Suspend
GBE0_MDI3+ A3 I/O Analog 3.3V max Suspend
GBE0_MDI3- A2 I/O Analog 3.3V max Suspend
GBE0_ACT# B2 OD CMOS 3.3V Suspend/3.3V
Connect to LED and recommend current limit
resistor 150ȟ to 3.3VSB
Gigabit Ethernet Controller 0 activity indicator, active low.
GBE0_LINK# A8 OD CMOS 3.3V Suspend/3.3V NC Gigabit Ethernet Controller 0 link indicator, active low.
GBE0_LINK100# A4 OD CMOS 3.3V Suspend/3.3V Connect to LED and recommend current limit
resistor 150ȟ to 3.3VSB Gigabit Ethernet Controller 0 100 Mbit / sec link indicator, active low.
GBE0_LINK1000# A5 OD CMOS 3.3V Suspend/3.3V
Connect to LED and recommend current limit
resistor 150ȟ to 3.3VSB
Gigabit Ethernet Controller 0 1000 Mbit / sec link indicator, active low.
Signal Pin# Pin Type Pwr Rail /Tolerance CD9A3 Series Carrier Board Description
SATA0_TX+ A16 O SATA AC coupled on Module AC Coupling capacitor
SATA0_TX- A17 O SATA AC coupled on Module AC Coupling capacitor
SATA0_RX+ A19 I SATA AC coupled on Module AC Coupling capacitor
SATA0_RX- A20 I SATA AC coupled on Module AC Coupling capacitor
SATA1_TX+ B16 O SATA AC coupled on Module AC Coupling capacitor
SATA1_TX- B17 O SATA AC coupled on Module AC Coupling capacitor
SATA1_RX+ B19 I SATA AC coupled on Module AC Coupling capacitor
SATA1_RX- B20 I SATA AC coupled on Module AC Coupling capacitor
ATA_ACT# A28 I/O CMOS 3.3V / 3.3V PU 10K to 3.3V
Connect to LED and recommend current limit
resistor 220ƻ to 3.3V
ATA (parallel and serial) or SAS activity indicator, active low.
Signal Pin# Pin Type Pwr Rail /Tolerance CD9A3 Series Carrier Board Description
PCIE_TX0+ A68 AC Coupling capacitor
PCIE_TX0- A69 AC Coupling capacitor
PCIE_RX0+ B68
PCIE_RX0- B69
PCIE_TX1+ A64 AC Coupling capacitor
PCIE_TX1- A65 AC Coupling capacitor
PCIE_RX1+ B64
PCIE_RX1- B65
PCIE_TX2+ A61 AC Coupling capacitor
PCIE_TX2- A62 AC Coupling capacitor
PCIE_RX2+ B61
PCIE_RX2- B62
PCIE_TX3+ A58 NA NA
PCIE_TX3- A59 NA NA
PCIE_RX3+ B58 NA NA
PCIE_RX3- B59 NA NA
PCIE0_CK_REF+ A88
PCIE0_CK_REF- A89
ȟ
ȟ
ȟ
ȟ
Device - Connect AC Coupling cap 0.1uF
Slot - Connect to PCIE Conn pin
Connect to PCIE device or slot
Device - Connect AC Coupling cap 0.1uF
Slot - Connect to PCIE Conn pin
Connect to PCIE device or slot
Connect to PCIE device, PCIe CLK Buffer or slot
Pin Types
I Input to the Module
O Output from the Module
I/O Bi-directional input / output signal
OD Open drain output
Connect to Magnetics Module MDI0+/-
Connect to Magnetics Module MDI1+/-
Connect to Magnetics Module MDI2+/-
Connect to Magnetics Module MDI3+/-
Connect to SATA0 Conn RX pin
Connect to SATA1 Conn TX pin
O PCIE AC coupled on Module PCI Express Differential Transmit Pairs 2
I PCIE AC coupled off Module PCI Express Differential Receive Pairs 1
O PCIE PCIE Reference clock output for all PCI Express and PCI Express Graphics lanes.
I PCIE AC coupled off Module PCI Express Differential Receive Pairs 3 (NA for CD9A3)
O PCIE AC coupled on Module PCI Express Differential Transmit Pairs 3 (NA for CD9A3)
I PCIE AC coupled off Module PCI Express Differential Receive Pairs 2
Device - Connect AC Coupling cap 0.1uF
Slot - Connect to PCIE Conn pin
AC97/HDA Signals Descriptions
Serial TDM data inputs from up to 3 CODECs.
Gigabit Ethernet Signals Descriptions
Gigabit Ethernet Controller 0: Media Dependent Interface Differential
Pairs 0,1,2,3. The MDI can operate in 1000, 100 and 10 Mbit / sec
modes. Some pairs are unused in some modes, per the following:
1000BASE-T 100BASE-TX 10BASE-T
MDI[0]+/- B1_DA+/- TX+/- TX+/-
MDI[1]+/- B1_DB+/- RX+/- RX+/-
MDI[2]+/- B1_DC+/-
MDI[3]+/- B1_DD+/-
Serial ATA or SAS Channel 1 receive differential pair.
SATA Signals Descriptions
O PCIE AC coupled on Module PCI Express Differential Transmit Pairs 1
PCI Express Lanes Signals Descriptions
Serial ATA or SAS Channel 0 transmit differential pair.
Serial ATA or SAS Channel 0 receive differential pair.
O PCIE AC coupled on Module PCI Express Differential Transmit Pairs 0
Serial ATA or SAS Channel 1 transmit differential pair.
I PCIE AC coupled off Module PCI Express Differential Receive Pairs 0
Connect to SATA1 Conn RX pin
Connect to SATA0 Conn TX pin
Connect to PCIE device or slot