Dexaplan VT 623 - Manual (Page 5)

First use
Operation
!
!
!
!
!
!
!
!
Plug the mains adapter [12] into a mains power socket. The operating
status LED [35] lights green and the nameplate cover [20] is
illuminated from the back.
Remove the protective film from the monitor [33].
The video door entry system is now ready for operation.
A visitor presses the doorbell button [21] of the outdoor station. A chime
sounds from the indoor station. The camera image is displayed on the
monitor [33] and the operating status LED [35] lights red. It can now be
heard on the indoor station what is said at the outdoor station.
If the visitor presses the doorbell button again, the chime sounds again.
Press the talk button [36] to speak to the visitor. The LED of the
talk button flashes blue.
Now speak into the microphone [39]. The visitor hears you by means
of the loudspeaker [19] of the outdoor station and can talk to you
using the microphone [22] of the outdoor station. You hear the visitor
by means of the loudspeaker [34] of the indoor station.
Press the talk button
again to end the conversation; otherwise
the connection will end automatically after 4 minutes. The LED of the
talk button stops flashing and the monitor image disappears.
If you do not react to the visitor pressing the doorbell button, the monitor
image disappears after approx. 60 seconds
You can only start the talk function when the monitor image is activated.
The chime and the conversation are relayed to a powered loudspeaker if
connected. If the powered loudspeaker has a volume control, you can
adjust the volume independently of the indoor station volume.
If a door opener is connected, you can unlock the door / gate as follows
With a latching door opener the door or gate remains open after the signal.
Press the door opener button [37]. The gate or the door is locked
again after it has been opened and closed again.
Keep the door opener button [37] pressed until the visitor has
opened the door. The door remains unlocked for the period in which
you keep the button pressed.
Release the door opener button and the door opener locks
immediately.
While the door opener button is pressed, the LED of the door opener button
flashes blue for approx. 2 seconds, the monitor image disappears for a
short time, “NO SIGNAL” is displayed briefly on the monitor and the
nameplate is not illuminated.
Unlocking the door / gate is only possible when the monitor image is
activated.
Note:
Note:
Door opener (optional)
Latching door opener
Non-latching door opener
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
Carefully make a hole using a pointed object in one of the
predetermined breaking points of the grommet [24].
Guide the connection cable [14] through this hole.
If required, make a second hole for the cable of an optional door
opener and guide the cable through this hole.
Connect the connection cable [14] to the terminals of the outdoor
station [59, 60] and the indoor station [55, 56] according to the
connection diagram (see Fig. I). Pay attention here to the wire
markings and the polarity (A to A, B to B).
If desired, connect an optional door opener [62] (see next chapter).
Replace and screw down the terminal cover on the outdoor station.
If desired, install an optional door opener [62] (not included in the
package contents) at the desired location according to the instructions
of the manufacturer.
Connect it to the terminals [57] and [58] of the outdoor station with a
two-core cable (polarity-independent) according to the connection
diagram (see Fig. I).
Connect an optional powered loudspeaker [48] (not included in the
package contents), e.g. a PC speaker, to the terminals [53] and [54]
of the indoor station with a two-core cable according to the connection
diagram (see Fig. I). Pay attention to the polarity for the connection.
Connect the low-voltage connector [13] to the connection [50].
For cable routing along the wall: Guide all connected cables through
the cable opening [25].
Slide the outdoor station [1] at an angle upwards into the wall bracket
and push it into place.
Fix the outdoor station to the wall bracket through the two holes [30]
with two of the fixing screws [4].
For cable routing through the wall: Place the connection cable [14]
into the cable channel [51].
For cable routing along the wall: Place the mains adapter cable into
the cable channel [51].
Slide the indoor station [2] at an angle upwards into the wall bracket
and push it into place.
Fix the indoor station to the wall bracket through the hole [47] with
one fixing screw [4].
Hang the indoor station [2] on the two protruding screw heads in the
wall using the keyhole slots [49].
Connecting an optional door opener
Connecting optional powered loudspeaker
Connecting the mains adapter to the indoor station
Finishing the outdoor station mounting
Finishing the indoor station mounting
Finishing the wall mounting
Screwing to the wall
Hanging on the wall
GB / IE - 7