Denon AV SURROUND RECEIVER AVR-5308CI User Manual
Page 82
MODE
SELECTOR
Remote ID
AMP
(MAIN)
TUNER
iPod
NET/DTU
(Analog
TUNER)
(XM)
(Net
Audio)
(HD
Radio)
1
(Default)
81001
52863
52864
72815
62865
62840
2
82001
52795
52812
72816
62837
62841
3
83001
52800
52813
72817
62838
62842
4
84001
52805
52814
72818
62839
62843
Setting the Remote ID
When using multiple DENON AV receivers in the same room,
make this setting so that only the desired AV receiver operates.
1
Press
[AMP]
to set the main remote control unit to the
AMP mode.
2
Press and hold in
[RC SETUP]
for at least 3 seconds.
The signal transmission indicator flashes twice.
3
Refer to the table at the right, and use
[NUMBER]
to
input the 5-digit number corresponding to the remote
ID to be changed.
The signal transmission indicator flashes twice.
4
Press
[TU]
,
[iPod]
or
[NET/DTU]
to select the mode to
be set.
5
Repeat steps 2 to 4 to set the remote IDs for all modes.
NOTE
• When changing a setting, be sure to set the same remote ID as the
AVR-5308CI’s (vpage 41).
• When changing the AMP mode’s remote ID, also change the
“TUNER”, “iPod” and “NET/DTU” remote ID at the same time.
• Set the remote ID of an analog tuner for “TUNER” (
), the XM
remote ID for “
”.
Learning Function
If your AV devices are of a brand other than DENON or if they
cannot be operated with the preset memory function, their
remote control signals can be transfered to stored in the AVR-
5308CI’s main remote control unit.
1
Press
[MODE SELECTOR]
for the device you want to
set.
2
Press and hold in
[RC SETUP]
for at least 3 seconds.
The signal transmission indicator flashes twice.
3
Press
[9]
,
[7]
and
[5]
, in that order.
The signal transmission indicator flashes twice and the learning
mode is set.
4
Press the button to be set.
The main remote control unit’s display turns off.
b
If a button that cannot be learned is pressed, the signal transmission
indicator lights but the signal is not learned.
5
Point the main remote control units directly at each
other and press and hold the button on the other
device’s remote control unit that you want to learn.
Once learning is completed normally, the display lights and the
signal transmission indicator flashes twice.
b
If you want to learn other buttons, repeat steps 4 and 5.
b
The mode can be switched by pressing
[MODE SELECTOR]
.
b
The signal transmission indicator lights once for a long time if
learning was not possible
6
Press and hold in
[RC SETUP]
for at least 3 seconds.
The signal transmission indicator flashes twice and the setting
is completed.
Get
ting Star
ted
Connections
Set
up
Pla
ybac
k
Remot
e Contr
ol
Multi-Zone
Inf
or
mation
Tr
oubleshooting
[NUMBER]
[MODE
SELECTOR]
[RC SETUP]
[CHANNEL+/–]
[SYSTEM CALL]
[ AMP]
[POWER ON]
[
NET/DTU]
[ TU]
[8], [9],
[1],
[6], [7],
[3], [2]
Other device’s
remote control unit
AVR-5308CI’s main remote
control unit (RC-1067)
Signal transmission
indicator
AVR5308CIEU_100_初校作成中.indd 79
2008/05/26 9:43:06