Signamax 8-Port 10/100/1000 Compact Gigabit Switch - Manual (Page 2)

065-7007 5-port and 065-7012 8-port 10/100BaseT/TX Ethernet Mini Switches
User’s Guide
065-7012G 8-port 10/100/1000BaseT/TX Ethernet Switch
Hardware
The following describes the front panel, rear panel and LED indicators of the Signamax 065-7012G 8-port
10/100/1000BaseT/TX Ethernet Compact Gigabit Switch.
Front Panel
LED Indicators
LED Color Status Description Number of LED
Power Green On Power on 1
On Link status of connected port Link/Act Green
Flashing Data Transmission Status of connected port
8
1000T Green On Gigabit Ethernet transmission on that port 8
Rear Panel
1. RJ-45 Ports
Eight Ethernet RJ-45 UTP ports all come with Auto-negotiation and operate at 10/100/1000 Mbps for connection to servers and hubs. All ports auto-detect
Full/Half-Duplex mode
2. Auto-MDIX Function
Any port can be used to connect to other switches or hubs without using a crossover cable.
3. Power Connector
Used to connect the external DC power adapter that connects to the power outlet.
Network Connection
The following sections describe the connections of the Signamax 065-7012G 8-port 10/100/1000BaseT/TX Ethernet Switch.
PC to Switch
A PC can be connected to the Signamax 065-7012G Switch via a Category 5e or better UTP/STP straight cable for Gigabit
Ethernet support. The PC (equipped with a RJ-45 10/100BaseT/TX 10/100 Mbps jack or a 10/100/1000BaseT/TX 10/100/1000
Mbps jack) should be connected to any of the eight ports.
Note: The LED indicators for PC connection are dependent on the LAN card capabilities. If LED indicators are not illuminated after making a proper connection,
check the PC LAN card, the cable, the N-Way Switch conditions, and the connections.
Switch to Switch or Switch to Hub
Another switch or a hub (10BaseT or 100BaseTX) can be connected to the Signamax 065-7012G Switch via a Category 3/4/5
UTP/STP straight cable. The connection is accomplished from any normal port of the Signamax 065-7012G Switch to any port
of the connected switch or hub.
Technical Specification
Standards: IEEE802.3 10BaseT Ethernet, IEEE802.3u 100BaseTX Fast Ethernet, 1000BaseT Gigabit Ethernet,
ANSI/IEEE std 802.3 N-Way auto-negotiation, IEEE802.3 Frame types: Transparent,
IEEE802.Sx flow control for Full-Duplex, Back Pressure flow control for Half-Duplex,
Auto-MDIX Function
Protocol: CSMA/CD
Topology: Star
Transmission Method: Store-and-forward
Transfer Rate:
Ethernet: 10 Mbps (Half-Duplex); 20 Mbps (Full-Duplex)
Fast Ethernet: 100 Mbps (Half-Duplex); 200 Mbps (Full-Duplex)
Gigabit Ethernet: 1000 Mbps (Half-Duplex); 2000 Mbps (Full-Duplex)
Media:
10BaseT: 2-Pair UTP Cat. 3,4,5 (100m); EIA/TIA-568 100-ohm STP (100m)
100BaseTX: 2-Pair UTP Cat. 5 (100m); EIA/TIA-568 100-ohm STP (100m)
1000BaseT: 2-Pair UTP Cat. 5e or better (100m); EIA/TIA-568 100-ohm STP (100m)
No. of Ports: Eight 10/100/1000 Mbps RJ-45 ports
MAC Address Table: 8K
Packet Filtering/Forwarding Rate: Wire-speed per port (for 1000 Mbps, 100 Mbps, & 10 Mbps)
Power: External Power Adapter 12V DC 0.6 A
Consumption: 3 watts maximum
Temperature: Operating: 32°C ~ 113°F (0°C ~ 45°C), Storage: 5°F ~ 140°F (-10°C ~ 60°C)
Humidity: Operating: 10% ~ 90%, Storage: 5% ~ 95%