Pinnacle Systems SLT Series - Manual (Page 6)

Pr Pr Pr Pr Proper Usa oper Usa oper Usa oper Usa oper Usag gg gge and Limita e and Limita e and Limita e and Limita e and Limitations tions tions tions tions
The information disclosed herein includes propriet ary
rights of the manufacturer. Neither this document nor the
information disclosed herein shall be reproduced or
transferred to other document s, used or disclosed to
others for manufacturing purposes, or for any other
purposes, except as specifically authorized in writing by
the manufacturer. If this manual is supplied in connection
with the sale or delivery of manufacturer’s equipment, it
is to be used solely for maintenance, repair, or installation
of such equipment.
The SLT Series was manufactured in the United States.
The Installation Manual was printed in the United States.
You must read and fully underst and the following
information pertaining to the proper use and limitations of
your Microguard:
• The SLT Series must be inst alled by qualified
personnel only.
• The SLT Series must NOT be used on full
revolution presses or any machine that cannot
be commanded to stop at any time.
• You must NOT wire the Safety Output cont acts
of the SLT Series to an external relay unless you
use the External Relay Checking feature.
• The mechanical power press on which the SLT
Series is installed must meet ANSI B11.1-1988
and OSHA 1910.217 regulations. These include
inspection and maintenance procedures that
must be followed to comply with the regulations.
The manufacturer will NOT take responsibility for
improperly maintained machinery.
• Point of operation safeguarding is defined in ANSI
B11.19-2003. This regulation is used to
determine a safe dist ance to place your SL T
Series. The manufacturer takes no responsibility
for injury as a result of improper safeguarding or
improper safe distances.
• The SLT Series may not be able to safely stop a
press which has a faulty stopping mechanism.
The manufacturer cannot be held responsible for
an improperly maint ained or faulty stopping
mechanism.
• The SLT Series must be checked before put into
operation. Follow instructions provided in this
manual for procedures on how to do this.
• The SLT Series should never be modified or
repaired except by qualified personnel and upon
authorization of the manufacturer. Never operate
machinery that is not in full working order.
• Make sure that all maintenance people, machine
operators, die-setters, foreman, and supervisors
have read and understood this manual and all
procedures have been and will be followed.
• All procedures in this manual must be followed.
The manufacturer cannot take responsibility for
operation if all procedures and warnings in this
manual are not followed.
W W W W War ar ar ar arrrrrranty anty anty anty anty
Manufacturer warrants that this product will be free from
defects in material and workmanship for a period of two
years from the date of shipment thereof. Within the
warranty period, the manufacturer will rep air or replace
(at our discretion) any product that is disclosed as defective
upon examination by the manufacturer and is returned
with shipping charges prepaid. This warranty will not apply
to any product that has been subjected to misuse,
negligence, accident, restriction, and use not in
accordance with manufacturer’s instructions or which will
have been altered or repaired by persons other than the
authorized agent or employees of the manufacturer.
Disc Disc Disc Disc Disclaimer laimer laimer laimer laimer
The provisions of the warranty are the sole obligations of
the manufacturer and exclude all other warranties of
merchantability, expressed or implied. Further, there are
no warranties that extend beyond the above warranty.
Limita Limita Limita Limita Limitation of tion of tion of tion of tion of Lia Lia Lia Lia Liability bility bility bility bility
In the event of any claim for breach of any obligations of
the manufacturer under any order, whether expressed or
implied, and particularly in the event of any claim of a
breach of the warranty or warranties cont ained in the
paragraph “Warranty” or of any other warranties,
expressed or implied which might despite the paragraph
entitled “Disclaimer,” be determined to be incorporated in
any order, the company shall under no circumstances be
liable for any consequential or special damages, either in
law or in equity, or for losses or expenses or claims for the
same arising from the use of, or inability to use, the
products of the manufacturer for any purpose whatsoever.
We have designed our equipment to the very highest
performance and safety standards known to the current
technological state of the art. However, the installation,
usage, suitability, and fitness of our equipment for any
purpose, known or unknown, is interdependent upon the
performance of other equipment not manufactured,
installed, or secured or maintained by the manufacturer.
We cannot and do not accept responsibility for any overall
system performance when factors, such as these, are
beyond our control.
WARNING:
The entire machine safety system must
be tested at the start of every shift. Machine testing
should include: (1) proper machine operation and
stopping capability; and (2) verification of proper
installation and settings of all point of operation guards
and devices before the operation is released for
production.