Oklahoma Sound #6010 - Manual (Page 2)

O
klahOma
S
Ound
C
OrpOratiOn ARiSTOCRAT SOuND FLOOR LECTERN: Model 6010
2 7
introduction
aristocrat sound lectern - model 6010
Perfect for the smallest to largest venues. Executive style podium includes
50 watt multimedia amplifier with two built in 8" speakers surrounded by
gold appointments. includes Microphones, Holders, Digital Timepiece and
rolls on four casters. For audiences up to 2,500 people. Assembly required.
Colors: Walnut, Light Oak, Med. Oak, Mahogany/Black Edging
Dimensions: 251/4" W x 46" H x 201/4" D.
assembly tips
• Do not use a sharp instrument such as a knife or a screwdriver to open the
packaging, as this may scratch or possibly damage the unit.
• All assembly should be done on a clean protected surface such as carpet
or the like.
• Make sure that you have all the required parts. A list of all the parts
is included.
• Read instructions carefully and follow diagrams to ensure easy and
correct assembly.
care oF your cabinet
• All exterior and interior exposed surfaces are melamine covered as well as
edges in matching patterned melamine material. To refresh the appear-
ance, wipe the surface with a cloth soaked lightly in furniture oil. Avoid
speaker grill area Your cabinet will look as good as new.
technical speciFications
Manufacturers Warranty
Our lectern undergoes the most rigid and exacting tests for superior quality and performance before
leaving the factory. Our lectern is made in America by American craftsmen. Oklahoma Sound
Corporation warrants this product to be free from defective material and workmanship for two years
from the date of resale by an authorized Oklahoma Sound distributor. Oklahoma Sound will replace
defective parts and repair malfunctioning products under this warranty when the defect occurs under
normal installation and use, provided the unit is returned to our factory via prepaid transporta-
tion after direct authorization and approval by Oklahoma Sound. This warranty provides that
examination of the returned product must disclose in our judgement, a manufacturing defect. This
warranty does not extend to any product which has been subject to misuse, neglect, accident, improper
installation, or where the serial number has been removed or defected and is given in lieu of any other
warranty implied or expressed and will not cover any consequential damages.
Power Output .......50W RMS at 10% THD
Mic ............................Electret Condenser Mic (2)
Aux ............................150 mV>220K
Frequency ..............100HZ-25KHZ
Response ................+ 3dB Power Supply ....110-120V ohms DC 10.8 12V
Fuse ......................2A normal
Output .................8 ohms
Accessories ........Handheld mic; clip-on mic;
gooseneck; Shockmount
mic holder; digital clock
700 series amplifier operating instructions
operating precautions
Before operating the amplifier, be sure you fully understand all instructions and
features of the amplifier. DO NOT turn amplifier on until all input and output
connections have been made. NEVER replace fuses unless power is off.
microphone input connection
The microphone input accepts 1/4" phone jack. Do not position microphone next
to or facing speakers. This may cause acoustic feedback.
auxiliary input
One auxiliary input is provided for radio tune; tape recorder, CD player or multi-
media equipment. Output level is adjusted by the auxiliary volume control.
tone/equalization controls
The Low and High frequency controls are similar to the bass and treble controls
found on most stereo systems. Optimum tone is achieved by first setting both
knobs halfway; adjust Low and High frequency controls to suit environment.
power supply 12V dc operation
Connect a 12 volt rechargeable battery 5 amp (not included) to the battery
input connector located on the panel of the amplifier (using 6' battery cable).
Be sure that the positive pole of battery is connected to the white wire terminal
(+) and the negative pole to the Brass wire (-). When lectern is plugged into a
standard wall outlet, the battery will automatically recharge. Green indicator
light illuminates during recharge mode.
precautions
• Set Mic volume control on lowest when turning unit on.
• Ensure correct polarity for D.C. supply connections.
• Reverse connections will blow the fuse and may damage internal circuitry.
• Always replace fuse with specified rating.
removal and installation of amplifier
if your amplifier has to be removed for servicing — follow these simple steps:
1) Disconnect A/C wall plug.
2) Remove 4 side screws two on each side panel under amp top.
3) Disconnect speaker wire at rear of amplifier.
4) Pack it into a strong box with ample cushioning and return to factory
5) To install new amplifier reverse the above procedure.