ABtUS AVS-SSR8/1-1 - Manual (Page 4)

Example:
Projector Command format:
POWER ON => 02H 00H 00H 00H 00H 02H
POWER OFF => 02H 01H 00H 00H 00H 03H
Video Source => 02H 03H 00H 00H 02H 01H 01H 09H 31H 12H 5FH AAH
RGB Source => 02H 03H 00H 00H 02H 01H 01H 09H 31H 12H 5FH
Coding set are as followed:
(1). POWER ON
Transmitted code : 53 45 54 52 06 50 57 4E 02 00 00 00 00 02
Confirm Return code : 52 54 55 4E 06 50 57 4E 02 00 00 00 00 02
(2). POWER OFF
Transmitted code : 53 45 54 52 06 50 57 46 02 01 00 00 00 03
Confirm Return code : 52 54 55 4E 06 50 57 46 02 01 00 00 00 03
(3). Input Source - 1
Transmitted code : 53 45 54 52 0C 56 44 31 02 03 00 00 02 01 01 09 31 12 5F AA
Confirm Return code : 52 54 55 4E 0C 56 44 31 02 03 00 00 02 01 01 09 31 12 5F AA
(4). Input Source - 2
Transmitted code : 53 45 54 52 0B 50 43 31 02 03 00 00 02 01 01 09 31 13 5F
Confirm Return code : 52 54 55 4E 0B 50 43 31 02 03 00 00 02 01 01 09 31 13 5F
RS-232 PROGRAMMING
ABtUS AVS-SSR8/1
2. Setting the Projector Communication parameter :
Header code (4 byte) + Data code length (1 byte) + Command ID (3 byte) + Data code (2 byte).
Header code : 53H 45H 54H 52H
Data code length : 02H
Command ID
: 42H 41H 55H
Data code : XXH YYH
XXH => Projector Baud rate and reference are as followed :
(1). 00H : 1200bps.
(2). 01H : 2400bps.
(3). 02H : 4800bps.
(4). 03H : 9600bps.
YYH =>Projector Data Length and Parity bit and reference are as followed :
(1). 00H : Data length 8bits, No Parity.
(2). 01H : Data length 8bits, Odd Parity.
(3). 02H : Data length 8bits, Even Parity.
(5). 04H : 19200bps.
(6). 05H : 38400bps.
(7). 06H : 115200bps.
to be continued..
OPERATION:
1) Setting the unit to “ IR Leaning mode ” :
Press and hold “UP” and “DOWN” button at the same time for 3 sec.
both “UP” and “DOWN” button LED will be blinking. “IR Learn Mode” activated.
1.1) Learning “Projector Power OFF”
In “IR Learn Mode”, press the “UP” button. The “UP” button LED will be blinking.
Point the Projector remote at about 1-2cm away from the “IR window”, press and
hold the “Power” button till the STOP LED is “ON”.
IR learning completed.
1.2) Learning “Projector Power ON”
In “IR Learn Mode”, press the “DOWN” button. The “DOWN” button LED will be blinking.
Point the Projector remote at about 1-2cm away from the “IR window”, press and
hold the “Power” button again till the STOP LED is “ON”.
IR learning completed.
1.3) Learning “Projector PC source select”
In “IR Learn Mode”, press the “UP” and “STOP” button at the same time.
The “UP” button LED will be blinking while the “STOP” button LED stays ON.
Point the Projector remote at about 1-2cm away from the “IR window”, press and
hold the “VGA Input” button till the STOP LED is “ON”.
IR learning completed.
1.4) Learning “Projector Video source select”
In IR Learn Mode, press the “DOWN” and “STOP” button at the same time.
The “DOWN” button LED will be blinking while the “STOP” button LED stays ON.
Point the Projector remote at about 1-2cm away from the “IR window”, press and
hold the “Video Input” button till the STOP LED is “ON”.
IR learning completed.
LEARING OF PROJECTOR IR CODE
Installation Guide
Important Note: After termination, if motor does not move.
Reset by switch on and off the incoming supply.
ABtUS AVS-SSR8/1 06 03