Turning auto reception on and off, Specifying the transmitter selection mode in japan, Calibration signal reception precautions – G-Shock GW-300BTJ-10JR User Manual
Page 2: Troubleshooting, Turning auto reception on and off 1
2
USER’S GUIDE 2609/2639
AUTO
With this setting, the watch automatically selects either the
Otakadoya Mountain signal (40kHz) or the Hagane Mountain
signal (60kHz), whichever is strongest.
* The frequency first used by the watch is the one that was
last successful.
40
With this setting, the watch always receives the Otakadoya
Mountain signal (40kHz).
60
With this setting, the watch always receives the Hagane
Mountain signal (60kHz).
Turning Auto Reception On and Off
1.
Display the setting screen.
Hold down the A
A
A
A
A button
for two seconds.
2.
Display the transmitter selection mode setting screen.
Press the CCCCC button three
times.
3.
Turn auto reception on or off.
Press the D
D
D
D
D button to
toggle auto reception ON
and OFF.
4.
Exit the setting screen.
Press the A
A
A
A
A button twice.
This exits the setting screen and returns to the normal
timekeeping screen.
The display also will return to the normal timekeeping screen
automatically if you do not perform any operation for about
two or three minutes.
Viewing the Last Reception Date and Time
In the Timekeeping Mode:
Press the D
D
D
D
D button.
This displays the date and time
that signal reception was
complete and the current time
and date were adjusted.
To return to the timekeeping
screen, press the D button
again.
The display also returns to the
normal timekeeping screen
automatically if you do not
perform any operation for about
one or two minutes.
Important!
The calibration signals received by this watch include two data
groups: an hour-minute-second group and a year-month-day group.
Both the hour-minute-second
group and year-month-day group
were not received. It will not
remain on the display if only the
hour-minute-second group is
received.
Specifying the Transmitter
Selection Mode in Japan
When Tokyo (TYO) is selected as the Home City, you can select
either of two different transmitters for reception.
1.
Display the setting screen.
Hold down the A
A
A
A
A button
for two seconds.
2.
Select the transmitter selection mode you want.
Press the D
D
D
D
D button.
3.
Exit the setting screen.
Press the A
A
A
A
A button twice.
This exits the setting screen and returns to the normal
timekeeping screen.
The display also will return to the normal timekeeping screen
automatically if you do not perform any operation for about
two or three minutes.
Time setting is incorrect following signal reception.
Possible Cause:
Summer time is turned on or the wrong
Home City is selected.
Corrective Measures:
Turn off summer time so the DST
indicator is not on the display.
Configure the watch for the correct DST
setting and Home City setting.
If you cannot receive the calibration signal or if the current time
setting is incorrect after signal reception, check the current setup
of the watch. The following are the watch's factory default
settings, which are configured automatically whenever you have
the battery of the watch replaced.
Auto Receipt
Transmitter
Home City
Summer Time
On
Auto Japan transmitter select
(40kHz/ 60kHz)
Tokyo
Auto switching in accordance
with signal data
Troubleshooting
Cannot perform manual reception.
Possible Cause:
The watch is not in the Timekeeping Mode
or World Time Mode.
The Home City is set to a city other than
TYO
(Tokyo), NYC (New York), CHI
(Chicago), DEN (Denver), or LAX (Los
Angeles).
Corrective Measures:
Perform manual reception while a time
screen is on the display in the Timekeeping
Mode or World Time Mode only.
Change Home City To TYO (Tokyo), NYC
(New York), CHI (Chicago), DEN
(Denver), or LAX (Los Angeles).
The
icon is not displayed even though auto reception is
turned on.
Possible Cause:
A single receive operation was not
successful.
Both the hour-minute-second group and
year-month-day group were not received.
The watch is not in the Timekeeping Mode
or World Time Mode when an auto
reception time is reached.
You performed manual reception, which
clears the icon from the display.
Corrective Measures:
Check to make sure the watch is in a
location where it can receive the signal.
Place the watch in a location where
reception conditions are good.
Make sure that the watch is in the
Timekeeping Mode or World Time Mode
during the auto reception times.
The icon disappears from the display
whenever you change the current time
setting manually.
Calibration Signal Reception
Precautions
Auto reception can be performed while the watch is in the
Timekeeping Mode or World Time Mode only.
Operating any button while auto reception is in progress will
cause the watch to beep and then exit the receive operation.
Make sure you are within the range of the calibration signal
transmitter before performing the receive operation. Remember
that geographic contours, nearby buildings, the season, and the
time of day can make reception impossible even when you are
within range of the transmitter.
Proper reception may be impossible if there is something blocking
the signal. If reception is unsuccessful, try again.
This watch is designed to adjust its current time setting in
accordance with the calibration signals transmitted in Japan and
the United States only. Note that you will need to make your own
adjustments when using this watch outside of Japan or the United
States, or in any area that is outside the range of one of the
receivable time calibration signal transmitters.
When the watch is unable to adjust its time signal using the
calibration signal for some reason, timekeeping accuracy is within
±
15 seconds per month.
Strong electrostatic charge can cause timekeeping error.
Signal reception is cancelled if an alarm starts to sound while it is
being performed.
The watch's calendar shows dates up to the year 2099.
Attempting a receive operation after that causes an error.
If only the hour-minute-second group is received, the Timekeeping
Mode date at the time of reception is recorded as the last
reception date.
displayed
not displayed
Hour-minute-second group and year-
month-day group received
Hour-minute-second group only received
Not displayed
The following explanation covers the radio-controlled timekeeping function only.
For other functions, go to the download page for Module 2608 or 2638,
which are the export models that have the same functions, except for radio-controlled timekeeping.