TracRac IM Contractor Rac - Manual (Page 4)

Contractor Rac Pro INSTRUCTION MANUAL 7 6 Contractor Rac Pro INSTRUCTION MANUAL TracRac Inc. 994 Jefferson Street, Fall River, MA 02721-4893 • 800-501-1587 TracRac Inc. 994 Jefferson Street, Fall River, MA 02721-4893 • 800-501-1587
Figure 13. Upright Parts.
10. Built forward crossbar assembly by following the steps of the
standard crossbar assembly except slide 4 bolts (item 1) into
bottom groove of the crossbar (2 per side). Attach the end caps.
Loosely attach the bracket assemblies to the crossbar using lock
nuts and 15mm socket.
11. Loosen two bolts (13mm socket) on the forward bracket assemblies.
Slide the nut bar into the cantilever groove on each side.
12A. Align the bracket with the end of the front cantilever.
12B. Tighten two bolts using 13mm socket (Torque 90-110 lbs).
12C. Tighten two nuts using 15mm socket (Torque 220-240 lbs) on each side.
12D. Press the end caps into the front and rear cantilevers.
Make sure that all bolts and nuts are tightened up.
Assembly is completed.
Figure 10. Forward Crossbar assembly.
Item
No.
1
2
3
Qty.
4
2
4
Table 6. Forward Crossbar assembly parts
Description
T-Bolt, M10-1.5X25
Bracket, Forward
Lock Nut #10-1.5
Part No.
HD-80218
01-25051
HD-23179
Figure 11A. Crossbar installation. DETAIL A.
Figure 11B. Crossbar installation. DETAIL B. Figure 12. End cap installation.
Item
No.
1
2
3
4
5
6
Qty.
1
2
1
1
2
2
Table 7. Upright Part Reference
Description
Cleat
Bolt 1/4-20X1.75”
Nut Bar
Spacer, Cantilever
Bushing, Oval Tube
Hex Flange Bolt, M8X1.25, 50mm
Part No.
PI-11009
HD-80136
FX-11139
PI-23327
FX-90138
HD-23163-1
Figure 14.
Cantilever
Clamp Parts.
Item
No.
1
2
3
4
Qty.
1
1
1
4
Table 8. Cantilever Clamp Part Reference
Description
Cantilever Clamp
Label, TracRac
Lock Nut M10X1.5
Bolt, M8X1.25, 35mm Hex
Part No.
01-11144
BL-22000-D
HD-23179
HD-23165
Figure 15. Forward
Bracket Parts.
Figure 16. Tie Down Kit.
Item
No.
1
2
3
Qty.
1
1
2
Table 9. Forward Bracket Part Reference
Description
Nut Bar
Bracket, Forward
Bolt, M8X1.25, 16mm Hex Flange
Part No.
FX-11139
01-11142
HD-23163
Item
No.
1
2
3
Qty.
2
2
2
Table 10. Tie Down Kit Part Reference
Description
Tie Down Zinc Diecast
Knob, Female 3/8-16 UNC
T-Bolt #3/8-16X1-1/8, SS
Part No.
10-25111
KB-90004
HD-80122
NOTES: Although the Contractor Rac is capable of carrying a maximum of 1250 lbs, evenly distributed between both racks,
the capability is limited to the strength of the truck sidewall it is mounted on. More information on back cover.
BRACKET
ASSMEBLY
1
BRACKET
ASSMEBLY
2
3
FORWARD
BRACKET
ASSMEBLY
TWO BOLTS
FRONT
CANTILEVER
NUT
BAR
CANTILEVER
GROOVE
TWO
BOLTS
TWO
NUTS
END CAP
P/N PI-23326
1
UPRIGHT
2
3
4
5
6
4 1
3 2
1
2
3
1
2
3