TracRac IM Contractor Rac - Manual (Page 2)

Contractor Rac Pro INSTRUCTION MANUAL 3 TracRac Inc. 994 Jefferson Street, Fall River, MA 02721-4893 • 800-501-1587
3. After selecting the correct hole pattern for your truck
(using Figure 3), plug up all other holes using the black
plastic rivets. Large rivet–on the top, small rivet–on
the bottom (Figure 4).
Figure 3. Footprint for base of uprights.
Contractor Rac Pro INSTRUCTION MANUAL TracRac Inc. 994 Jefferson Street, Fall River, MA 02721-4893 • 800-501-1587
Installation Notes:
• Contractor Rac Pro mounts onto the side rails of your truck without drilling.
• Installation is straight forward, and should take approximately 45 minutes to complete.
1. Verify that you have received the correct parts using the assembly drawing and packing list.
Contractor Rac Pro
2. Install the cleat using two bolts (3/16” Allen
Wrench). Loosely attach bottom of the corner
braces to all four uprights using hex bolt
(16mm socket).
Table 1. Tools Required
1) Socket Wrench
2) 13mm, 15mm, 16mm
and 17mm Sockets
3) 5mm Allen Wrench
4) 3/16” and 5/16”
Allen Wrench
Recommended
1) Torque Wrench
Figure 2. Cleat and Corner Brace installation.
Figure 1. Contractor Rac Pro Installed on a truck bed.
Item
No.
1
2
3
4
5
Qty.
1
2
1
1
1
Table . Cleat and Corner Brace Parts
Description
Cleat
Bolt 1/4-20X1.75
Corner Brace
Hex Bolt,
M10-1.5X25
Heavy Washer,
M10, THICK
Part No.
PI-11009
HD-80136
01-22008
HD-23143-1
HD-23193
Item
No.
1
2
Qty.
15
15
Table 3. Plastic Rivets
Description
Rivet, Small, Ratchet, Black
Rivet, Large, Ratchet, Black
Part No.
PI-23328
PI-23329
4. Attach rubber block assembly and rubber shim to uprights
using socket head cap bolt, washer, rubber shim, rubber
block and brass square pocket nut, see Figure 4. Complete
all four upright assemblies. Do not attach the L-Rail
clamps (items 1,9 and 10), see Figure 5. NOTE: Match
the hole patterns in the rubber shims to the correct
upright. Flat surface of rubber shim must face down.
Figure 4. Front upright
assembly.
Item
No.
1
2
3
4
5
6
7
8
9
10
Qty.
4
2
2
2
1
1
1
1
2
2
Table 4. Upright Assembly Parts
Description
Bolt Socket Head Cap, 3/8-16x3.00”
3/8 Washer, THIN
Rubber Block
Sq Pocket Nut, Brass
Rubber Shim, Front LH
Rubber Shim, Front RH
Rubber Shim, Rear LH
(Not Shown)
Rubber Shim, Rear RH
(Not Shown)
Clamp, L-Rail
U-Channel 3” Long
Part No.
HD-11011
HD-80078
RX-11031
01-2100N
FX-23269
FX-23270
FX-23271
FX-23272
01-23222
01-22911
1
UPRIGHT
2
3
4 5
FRONT
DODGE
FORD F150
CHEVY
TOYOTA TUNDRA
RH
GMC
FORD F250/350
UPRIGHT BASE
(VERTICAL OVAL TUBE
NOT SHOWN)
TOYOTA TUNDRA
DODGE
FORD F150/250/350
CHEVY
GMC
RH
REAR
LH
LH
SNAP IN THEM TOGETHER
UPRIGHT BASE BETWEEN
THEM NOT SHOWN
10
2
FRONT
UPRIGHT
LH
FRONT
UPRIGHT
RH
RUBBER SHIM
FLAT FACES DOWN
SMALL
RIVET
LARGE
RIVET
5
6
9
1
2
1
3 4