SkyRC Toro Micro M25 25A ESC for 1/18 Car User Manual

Page 2

Programmable Features

Note: Factory Defaults are indicated by asterisk (D)*

At this point the TORO Micro will be flashing/beeping
the following sequence: Beep-Pause-Beep... and
then repeats.
This indicates that you are at Question 1 and it is
asking to accept/reject value 1.

When answering a question, you will need to move the
trigger to yes (full throttle) position or the no (full brake)
position and keep it there for about 3 seconds. When the
ESC has accepted your answer it will confirm your reply
by flashing the LED and emitting a beeping tone. Release
the trigger allowing it to go to Neutral to confirm that you
are ready for ESC to ask you next question. You are not
required to continue through all eight programming options.
For example, if you wish only to change the Brake/Reverse
Type (Option 1) then after programming that setting you
can disconnect power from the ESC and you're ready to
run. Disconnecting the controller in the middle of
programming simply retains the values for the remaining
programming options that were previously set up.

SPEED CONTROL SPECIFICATION

Controls, TORO Micro

Fwd/Brk or Fwd/Brk/Rev

Input Power (Cells)

2-3S LiPo, 4-12 NiCd/NiMH

Brake

On Resistance,Brushless

0.002 Ohm Per Phase

Continuous / Burst Current 25 Amp / 90Amp

Linear BEC

5 Volts, 1 Amp

Dimensions(LxWxH)

Weight (With wires)

Status LED

1 with 3 color
(Red, Green & Orange)

Thermal Overload Protection

Yes

30x26.1x13.8mm
(1.18x1.03x0.54in)

26g (0.92oz)

Proportional

Problem:

My TORO ESC may or may not arm, but

it will not calibrate to my transmitter

TROUBLE SHOOTING

Solution:

Try moving the throttle trim one way, then

the other (usually towards the throttle side
is best). If your transmitter has a 50/50 and
70/30 setting for the throttle, set it for 50/50
and retry calibration. Also, if you have
changed the dead band to a narrower band
you may want to try going back to the

ormal

setting.

Problem: My battery pack is plugged into the ESC
and nothing is working

Solution: Make sure the ESC's receiver plug is

plugged into channel 2 on the receiver

with the correct orientation. Check solder
connections and make sure the battery is
showing good voltage.

Problem:

My ESC calibrates for the full throttle and

full brake positions but won't calibrate to
the neutral throttle position. (Orange LED
keeps flashing)

Most calibration issues can be solved by
changing settings on the transmitter. Make
sure you have both your throttle and brake
endpoints (called EPA or ATV on your radio)
on the throttle channel out to between 100
to 120%. Make sure if you have a Futaba or
Futaba made transmitter to have the throttle
channel set to the reversed position.

Manufactured by
SKYRC TECHNOLOGY CO., LTD.
www.skyrc.com

The TORO Micro Brushless ESC is guaranteed to be
free from defects in materials or workmanship for a
period of ONE YEAR from the original date of purchase
(verified by dated, itemized sales receipt). Warranty
does not cover incorrect installation, components worn
by use, damage to case or exposed circuit boards,
damage due to timing, damage from using more than 3
Li-Po cells input voltage, cross-connection of battery/
motor power wires, overheating solder tabs, reverse
voltage application, improper use or installation of
external BEC, damage resulting from thermal overload
or short-circuiting motor, damage from incorrect
installation of FET servo or receiver battery pack,
tampering with internal electronics, allowing water,
moisture, or any other foreign material to enter ESC or
get onto the PC board, incorrect installation/wiring of
input plug plastic, allowing exposed wiring or solder
tabs to short-circuit, or any damage caused by a crash,
flooding or natural disaster. Because SKYRC has no
control over the connection & use of the speed control
or other related electronics, no liability may be assumed
nor will be accepted for any damage resulting from the
use of this product.Every SKYRC speed control & motor
is thoroughly tested & cycled before leaving our facility
and is, therefore, considered operational. By the act of
connecting/operating speed control, user accepts all
resulting liability. In no case shall our liability exceed

PRODUCT WARRANTY

SPECIFICATIONS ARE SUBJECT TO CHANGE
WITHOUT NOTICE.

6/10

7/10

8/10

9/10

10/10

Ver. 1.02(201009)

Plug Battery into the TORO Micro
Hold full throttle on your transmitter
Turn the ESC switch ON
TORO Micro flashes LED and rings once
Wait few seconds.
TORO Micro flashes LED and rings 4 times
indicating that it is ready for CALIBRATION mode
Continue to hold full throttle
TORO Micro flashes LED while beeping
Wait another few seconds
TORO Micro flashes LED and rings 4 times
TORO Micro flashes LED while beeping indication
that you are in PROGRAMMING mode
Let trigger go neutral (Centre)

How to Enter Programming Mode

YEAR

the product's original cost.