SkyRC Toro One Cell 120A ESC for 1/12 Car - Manual (Page 2)

IMPORTANT NOTE: Calibration is necessary for the first use of the ESC, or whenever
used with a new/different transmitter.
Individual transmitter's signals for full throttle, full brake and neutral vary. You must
calibrate your ESC so that it will operate more effectively with your transmitter.
1)Programming Card(Optional Part)
Instruction for Program Card
3/8 4/8
From this point on, when you connect batteries and turn on the switch, the ESC will give the
initialization tone and flash, and the arming tone will ring second or two later. If the ESC is
programmed for the Auto-Lipo setting, it will beep the number of cells in you Lipo pack
between the initialization tones and the arming tones. After the arming tone plays, the ESC will
ACTIVE and will respond to the throttle application.
ESC/TRANSMITER CALIBRATION
For users with a Futaba Transmitter, you must reverse the throttle channel signal on
your transmitter. Please refer to your Futaba instructions.
Red LED blinks whiles beeping, indicating it's time to push full
brake. Move throttle trigger to full brake and wait few seconds,
the ESC will blink red LED and rings 1second indicating full brake
measure.
Yellow LED blinks whiles beeping, indicating it's time for neutral.
Relax trigger to neutral (center). The ESC will now ring 1 second
and flash the yellow LED rapidly to accept the neutral position.
ESC will blink LED and ring one second indicating that it is armed.
ESC PROGRAMMING
Ver. 1.1 Ver. 1.1
How to Calibrate ESC
ESC switch OFF.
Turn on the Transmitter.
Hold full throttle on your transmitter and turn the ESC's switch ON.
Keep holding full throttle on the transmitter. The ESC will flashes
LED and ring the initialization tones.
Wait 2 seconds
Green LED blinks rapidly and the motor will rings 1 second indicating
full throttle measured.
3)Manual Programming
Manual Programming TORO 1 cell is as simple as answering a few questions. The
TORO 1 cell asks questing by beeping a setting number, followed by the possible
setting values. There are eight settings that can be programmed in the TORO .
CONNECTIONS
Connect motor sensor harness to ESC. Insert the 6 pin connector on the end of
the motor's sensor wires into ESC's sensor harness socket.
Connect ON/OFF switch to power output pins.
Connect Throttle lead to ESC and other end to the Receiver (Throttle Channel, Ch2)
Connect ESC to battery pack
One cell battery pack
TORO
Sensor-based
Brushless motor
(540-class)
Receiver
ESC ON/OFF
switch
Throttle lead
Orange motor
phase wires
(phaseC)
Sensor
harness
Red power wire
(battery positive)
Black power wire
(battery negative)
1S Li-Po battery
Battery connector
Power capacitor
Blue motor
phase wires
(phaseA)
Yellow motor
phase wires
(phaseB)
Fan
output
pins Switch
output
pins
2)SKYLink Programming Interface(Optional Part)
Optional fully adjustable PC interface,which includes a USB cord and USB Interface
One cell battery pack
Programming Card allows you to modify the most commonly used settings in your TORO 1
cell controller all at the touch of a single button. No computer needed. Simply connect the
Programming Card to the SKYLink interface pins of the controller and power the programming
card as described below. Click the button to scroll through and change the indicated
settings. All the settings will show on the programming card at once. Can't get any easier!
Turn off the ESC.
Connect the lead from program card
to the SKYLink interface pins of
the controller.
Turn on the ESC to apply power to
both ESC and Program Card.
All the current settings will be
displayed on the correspond LEDs.
Press and release button to move
between settings.
Press and hold button to change the
value for that setting.
Turn off the ESC and disconnect lead
from Program Card.
Instruction for Program Card
SKYLink
interface Pins +
S
SKYLink interface pins allows you to connect the Program Card and SKYLink Interface
Adaptor to you ESC directly for easy programming.
SKYLink
interface pins