SkyRC Cheetah 1/10 60A Sensored Combo - Manual (Page 2)

WARRANTY AND SERVICE
The Cheetah 1/10 CS60 60A Sensored ESC is guaranteed to be free from defects in
materials or workmanship for a period of 90 DAYS from the original date of purchase
(verified by dated, itemized sales receipt). Warranty does not cover incorrect installation,
components worn by use, damage to case or exposed circuit boards, damage due to timing,
damage from using more than 3 LiPo cells input voltage, cross-connection of battery/motor
power wires, overheating solder tabs, reverse voltage application, improper use or
installation of external BEC, damage resulting from thermal overload or short-circuiting
motor, damage from incorrect installation of FET servo or receiver battery pack, tampering
with internal electronics, allowing water, moisture, or any other foreign material to enter ESC
or get onto the PC board, incorrect installation/wiring of input plug plastic, allowing exposed
wiring or solder tabs to short-circuit, or any damage caused by a crash, flooding or natural
disaster. Because SKYRC has no control over the connection & use of the speed control or
other related electronics, no liability may be assumed nor will be accepted for any damage
resulting from the use of this product. Every SKYRC speed control & motor is thoroughly
tested & cycled before leaving our facility and is, therefore, considered operational. By the
act of connecting/operating speed control, user accepts all resulting liability. In no case shall
our liability exceed the product's original cost. We reserve the right to modify warranty
provisions without notice. This product is not intended for use by children under 14 years of
age without the strict supervision of an adult. Use of this product in an uncontrolled manner
may result in physical damage or injuries take extra care when operating any remote control.
Manufactured by
SKYRC TECHNOLOGY CO., LTD.
www.skyrc.com
SPECIFICATION
Constant/Burst Current
Motor Compatible
Car Compatible
Motor Limits
Resistance
Battery Cell Count
BEC Output
Size
Weight
FAN
60A/380A
Brushless Sensor & Sensorless ESC
1/10 and 1/12 Buggy and Touring Car
1/10 and 1/8 Crawlers
0.0007ohm
6V@3A
39x38x20mm (LxWxH)
30g (w/o wire)
[email protected] , Max 12.6V
Programmable Items and Description
14
+Yr DAYS
90
2013 SkyRC Technology Co., Ltd. All Rights Reserved.
Ver 1.0 7504-0369-01
6/6 5/6
Program Item Description
Auto LiPo
None
5V
6V
9V
12V
3.0V
3.1V
3.2V
3.3V
0%-30% (in 5% increment)
0%-100% (in 10% increment)
0-30 (in 5 increment)
Small
Normal
Large
Proportional Rev. Lock Out
Proportional w/o Reverse
FWD to Brake and Reverse
0°-30° (in 5° increment)
ESC Sensor
Normal
Reverse
Cut Off Voltage
Auto-Lipo Cut Off Volts/CELL
Drag Brake
Brakes Strength
Punch Strength
Dead Band
Reverse Type
Moto Timing (Sensor Only)
ESC Type Setting
Moto Direction
Factory Default Setting
10%
80%
10
10°
Auto
ESC ON/OFF: When the ESC is OFF, press the switch once, the motor will ring beep once and
the red LED will stay on (The factory default motor turbo timing is 10°), then the ESC is ready to
work. When the ESC is on, press the switch once, the LED will extinguish and the ESC is OFF.
Explanation of LED Indicator
ESC ON/OFF AND LED INDICATOR
1.
2.
The throttle trigger is in neutral position
The throttle trigger is in neutral position
The motor is running while the throttle trigger doesn’t
reach to the highest throttle/brake position
The throttle trigger is at the highest throttle/brake position.
Red LED is blinking (zero timing)
Red LED stays on
(Motor turbo timing is on)
Green LED is blinking.
Green LED stays ON
4/6
After running at full load, the ESC will be very hot. In this case, please turn off the ESC
after it cools down.
When the motor is running, the ESC can't be powered off by pressing the switch; when the
motor stops working, the ESC can be powered off. In an emergency, please disconnect
the battery to power off the ESC.
When the motor is running, keep the trigger of the transmitter to full brake for 8 seconds,
the ESC will be off. 1:
2:
3:
Instruction for Program Card
Programming Card
Programming Card allows you to modify the most commonly used settings in your Cheetah
1/10 CS60 60A Sensored ESC controller all at the touch of a single button. No computer
needed. Simply connect the Programming Card to the throttle lead of the controller and
power the programming card as described below. Click the button to scroll through and
change the indicated settings. All the settings will show on the programming card at once.
Can't get any easier!
Turn off the ESC.
Connect the lead from program card’s 3 pins
connector to the program interface pins of the
ESC. (Please refer ESC’s Instruction Manual
for details. The connection methods for
different ESC may varies)
Turn on the ESC to apply power to both ESC
and Program Card.
All the current settings will be displayed on
the correspond LEDs.
Press and release button to move between
settings.
Press and hold button to change the value for
that setting.
Turn off the ESC and disconnect lead from
Program Card.
2-3S LiPo 4-9S NiMH or
5-6S NiMH or 2S LiPo-- ≥8.5T(1/10 Touring Car), ≥10.5T(1/10 Buggy)
8-9S NiMH or 3S LiPo-- ≥10.5T(1/10 Touring Car), ≥13.5T(1/10 Buggy)
CAUTION:
ESC PROGRAMMING