SkyRC Toro SC120A ESC - Manual (Page 2)

SPECIFICATION
Constant/Burst Current
Motor Compatible
Car Compatible
Motor Limits
Resistance
Battery Cell Count
BEC Output
Size
Weight
FAN
WARRANTY AND SERVICE
The TORO SC120 Brushless Sensored 120A ESC is guaranteed to be free from defects in
materials or workmanship for a period of 90 DAYS from the original date of purchase
(verified by dated, itemized sales receipt). Warranty does not cover incorrect installation,
components worn by use, damage to case or exposed circuit boards, cross-connection of
battery/motor power wires, overheating solder tabs, reverse voltage application, improper
use or installation of external BEC, damage resulting from thermal overload or short-
circuiting motor, damage from incorrect installation of FET servo or receiver battery pack,
tampering with internal electronics, allowing water, moisture, or any other foreign material to
enter ESC or get onto the PC board, incorrect installation/wiring of input plug plastic,
allowing exposed wiring or solder tabs to short-circuit, or any damage caused by a crash,
flooding or natural disaster. Because SKYRC has no control over the connection & use of
the speed control or other related electronics, no liability may be assumed nor will be
accepted for any damage resulting from the use of this product. Every SKYRC speed control
& motor is thoroughly tested & cycled before leaving our facility and is, therefore, considered
operational. By the act of connecting/operating speed control, user accepts all resulting
liability. In no case shall our liability exceed the product's original cost. We reserve the right
to modify warranty provisions without notice. This product is not intended for use by children
under 14 years of age without the strict supervision of an adult. Use of this product in an
uncontrolled manner may result in physical damage or injuries take extra care when
operating any remote control.
Manufactured by
SKYRC TECHNOLOGY CO., LTD.
www.skyrc.com
120A/760A
Brushless Sensor or Sensorless ESC
1/10 SC or Monster, 1/8 SC or Buggy
KV ≤6000
0.0003ohm
6-12S NiMH or 2-4S LiPo
6V@3A, Linear
57x38x35mm (LxWxH)
76g (w/o wire)
[email protected]
ESC PROGRAMMING
The ESC can be programmed by program box, PC (connected with SKYLINK) or smart phone
via bluetooth module.
Profiles Preset
The users could preset and store 10 sets of profiles in the ESC. These data could be called
out for application at any time without any special program setting. The user could also reset
the profile according to his request. There is one factory default setting called Profile One
which is used for 1/10 Short Course or Monster.
Setting Details of Profile One
Running Mode
Motor Direction
Reverse Speed
Voltage Cutoff
ESC Overheat Protection
Motor Overheat Protection
Punch Rate Switch Point
1st Stage Punch Rate
2nd Stage Punch Rate
TH Input Curve
Throttle Dead Band
Throttle Status
Drag Brake
Brake Strength
Initial Brake
Brake Rate Switch Point
1st Stage Brake Rate
2nd Stage Brake Rate
Brake Input Curve
Program Item Section
General
Setting
Throttle
Control
Brake
Control
Description
Forward/Brake
Normal
25%
Auto(3.2V/1S)
105℃/221℉
105℃/221℉
50%
5
5
Line
0.080ms
10%
75%
=Drag-Brabe
50%
10
16
Line
14
+Yr DAYS
90
Profile One Setting Value (Default Value)
8/8
2013 SkyRC Technology Co., Ltd. All Rights Reserved.
Ver 2.0 7504-0400-02
7/8 6/8 5/8
KV ≤4000
1. PC via SKYLINK (optional part SK-600013)
2. Smart Phone via Bluetooth Module (optional part SK-600058)
3. Program Box (optional part SK-300046)
Red power wire
(battery positive)
Battery
Pack
Black power wire
(battery negative)
Power
Switch
Programmable Items and Description
Program Item
Running Mode
Motor Direction
Reverse Speed
Voltage Cutoff
ESC Overheat Protection
Motor Overheat Protection
Punch Rate Switch Point
1st Stage Punch Rate
2nd Stage Punch Rate
TH Input Curve
Throttle Dead Band
Throttle Status
Drag Brake
Brake Strength
Initial Brake
Brake Rate Switch Point
1st Stage Brake Rate
2nd Stage Brake Rate
Brake Input Curve
Section
General
Setting
Throttle
Control
Brake
Control
Forward/Brake
Normal
25-100% (in 1% increment)
3.0-25V (in 0.1V increment)
85℃/185℉
85℃/185℉
1-99%(in 1% increment)
1-30
1-30
Line
0.002-0.150ms
0-100%(in 1% increment)
0-100%
=Drag Brake
1-99%(in 1% increment)
1-20
1-20
Line
Forward/Brake/Reverse
Reverse
Auto (3.2V)
105℃/221℉
105℃/221℉
Custom
0-50%
Custom
Description
Forward/Reverse
125℃/257℉
125℃/257℉
Disable
Disable
Turbo
0-10 deg Turbo Timing
Turbo Full TH Delay
Turbo Engage Slope
Instant
1 deg/0.1S - 64 deg/0.1S
Turbo
Turbo Timing
Turbo Full TH Delay
Turbo Engage Slope
0 deg
0.10S
48 deg/0.1S
6S NiMH or 2S LiPo
For 1/10 Short Course and Monster, 1/10 sensor brushless motor for Short Course,
KV4600 4Poles, 2S LiPo
7-9S NiMH or 3S LiPo
10-12S NiMH or 4S LiPo KV ≤3000
Battery
Pack
Black power wire
(battery negative)
PC
Red power wire
(battery positive)
Battery
Pack
Black power wire
(battery negative)
Red power wire
(battery positive)
Bluetooth
SMART
PHONE
If you set the cut-off voltage manually, please note the adjustable votage is TOTAL cut-off
voltage of the battery pack. In AUTO mode, the default cut-off voltage is 3.2V/S, for
example, the cut-off voltage of a 4S battery pack is 3.2V*4=12.8V in AUTO mode.
For any repair or replace service, please contact your dealer in the first instance, who is
responsible for processing guarantee claims.
0.01-1.00S
Power
Switch
Power
Switch