SkyRC 1/5 EX 200A ESC - Manual (Page 2)

Power
Switch
Black power wire
(battery negative)
Red power wire
(battery positive)
Battery
Pack
3. Program Box (optional part SK-300046)
SPECIFICATION
Constant/Burst Current
Motor Compatible
Car Compatible
Motor Limits
Resistance
Battery Cell Count
BEC Output
Size
Weight
WARRANTY AND SERVICE
The TORO BEAST 1/5 200A ESC is guaranteed to be free from defects in materials or
workmanship for a period of 90 DAYS from the original date of purchase (verified by dated,
itemized sales receipt). Warranty does not cover incorrect installation, components worn by
use, damage to case or exposed circuit boards, cross-connection of battery/motor power
wires, overheating solder tabs, reverse voltage application, improper use or installation of
external BEC, damage resulting from thermal overload or short-circuiting motor, damage
from incorrect installation of FET servo or receiver battery pack, tampering with internal
electronics, allowing water, moisture, or any other foreign material to enter ESC or get onto
the PC board, incorrect installation/wiring of input plug plastic, allowing exposed wiring or
solder tabs to short-circuit, or any damage caused by a crash, flooding or natural disaster.
Because SKYRC has no control over the connection & use of the speed control or other
related electronics, no liability may be assumed nor will be accepted for any damage
resulting from the use of this product. Every SKYRC speed control & motor is thoroughly
tested & cycled before leaving our facility and is, therefore, considered operational. By the
act of connecting/operating speed control, user accepts all resulting liability. In no case shall
our liability exceed the product's original cost. We reserve the right to modify warranty
provisions without notice. This product is not intended for use by children under 14 years of
age without the strict supervision of an adult. Use of this product in an uncontrolled manner
may result in physical damage or injuries take extra care when operating any remote control.
Manufactured by
SKYRC TECHNOLOGY CO., LTD.
www.skyrc.com
200A/800A
Brushless Sensorless ESC
1/5 Off Road, On Road
0.0002ohm
4-8S LiPo
6.0V/7.4V @ 15A
111x44x37mm (LxWxH)
359g (without wire)
Profiles Preset
The users could preset and store 10 sets of profiles in the ESC. These data could be called
out for application at any time without any special program setting. The user could also reset
the profile according to his request.
14
+Yr DAYS
90
Profile One Setting Value (Default Value)
8/8
2014 SkyRC Technology Co., Ltd. All Rights Reserved.
Ver 2.2 7504-0497-02
7/8 6/8 5/8
KV ≤1100, 4 Poles
Programmable Items and Description
Program Item
Running Mode
Motor Direction
Reverse Speed
Voltage Cutoff
ESC Overheat Protection
Punch Rate Switch Point
1st Stage Punch Rate
2nd Stage Punch Rate
TH Input Curve
Throttle Dead Band
Throttle Status
Drag Brake
Brake Strength
Initial Brake
Brake Rate Switch Point
1st Stage Brake Rate
2nd Stage Brake Rate
Brake Input Curve
Section
General
Setting
Throttle
Control
Brake
Control
Forward/Brake
Normal
25-100% (in 1% increment)
9.6-42V (in 0.1V increment)
85℃/185℉
1-99%(in 1% increment)
1-30
1-30
Line
10-150us
0-100%(in 1% increment)
0-100%
=Drag Brake
1-99%(in 1% increment)
1-20
1-20
Line
Forward/Brake/Reverse
Reverse
105℃/221℉
Custom
0-50%
Custom
Description
Forward/Reverse
125℃/257℉ Disable
If you set the cut-off voltage manually, please note the adjustable voltage is TOTAL cut-off
voltage of the battery pack.
For any repair or replace service, please contact your dealer in the first instance, who is
responsible for processing guarantee claims.
ESC ON/OFF: When the ESC is OFF, press the switch once, the motor will ring beep once and
the red LED will blink, then the ESC is ready to work. When the ESC is on, press the switch
once, the LED will extinguish and the ESC is OFF or push the throttle trigger to the maximum
brake, hold for 8 seconds and the ESC is OFF.
Explanation of LED Indicator
ESC ON/OFF AND LED INDICATOR
1.
2.
The throttle trigger is in neutral position
The motor is running while the throttle trigger doesn’t
reach to the highest throttle/brake position
The throttle trigger is at the highest throttle/brake position.
Red LED is blinking
Green LED is blinking
Green LED stays ON
ESC PROGRAMMING
The ESC can be programmed by program box, PC (connected with SKYLINK) or smart phone
via Wi-Fi module.
1. PC via SKYLINK (optional part SK-600013)
2. Smart Phone via Wi-Fi Module (optional part SK-600075)
SMART
PHONE
Black power wire
(battery negative) Red power wire
(battery positive)
Battery
Pack
PC
WiFi Module
Data
Storage
Mode
Start and Stop Control
Choose data types to save
Data Saving Time increment
Single
Start storage once entering
in main program
Cycle
Press control storage
entering in main program
0.1S-10S
Voltage Current Throttle
Current
RPM ESC
Temperature
Running Mode
Motor Direction
Reverse Speed
Voltage Cutoff
ESC Overheat Protection
Punch Rate Switch Point
1st Stage Punch Rate
2nd Stage Punch Rate
TH Input Curve
Throttle Dead Band
Throttle Status
Drag Brake
Brake Strength
Initial Brake
Brake Rate Switch Point
1st Stage Brake Rate
2nd Stage Brake Rate
Brake Input Curve
Program Item Section
General
Setting
Throttle
Control
Brake
Control
Description
Forward/Brake
Normal
25%
25.6V
105℃/221℉
50%
5
5
Line
0.080ms
10%
75%
=Drag Brabe
50%
10
16
Line
BEC Voltage 6V
BEC Voltage 6V 7.4V
Power
Switch
Black power wire
(battery negative)
Red power wire
(battery positive)
Battery
Pack
When the motor is running, the ESC can't be powered off by pressing the switch;
when the motor stops working, the ESC can be powered off. In an emergency,
please disconnect the battery to power off the ESC. Note 2:
Note 1: After running at full load, the ESC will be very hot.