Warning – Sioux Tools STXG10S User Manual
Page 3
Form ZCE731A
3
Date
2014October6/F
LUBRICATION
All models may operate without airline lubrication. However, operating the tool without airline lubrication may reduce tool performance and vane life.
If an airline lubrication is not used, it is recommended that the tool be oiled daily before use to improve performance. Add 2-4 drops of air motor oil and run the
tool for 10-20 seconds to distribute oil through the tool.
For maximum performance and tool life, an air line lubricator, set to deliver 2 drops per minute, is recommended. SIOUX No. 288 Air Motor Oil is
recommended.
MAINTENANCE
Water, dust and other airline contaminants can cause rust and vane sticking. For long periods between tool use, flush the tool with a few drops of oil and run
for 10 seconds. This will help remove contaminants and reduce the formation of rust.
OPERATION
The tool is equipped with a locking type lever in order to prevent accidental start-up.
Speed of the tool may be adjusted by turning the regulator, which is located opposite the throttle lever.
INSTALLING MOUNTED WHEELS
Insert the mounted wheel into the collet. Make sure the wheel shank and the collet size match. Do not allow the wheel to extend beyond the collet an excessive
distance.
Hold the collet body with a 9/16” (14mm) wrench and the collet nut with a 3/4” (19 mm) wrench.
Turn the collet nut to the right and firmly tighten the collet on to the wheel shank.
REMOVING MOUNTED WHEELS
To remove the mounted wheel, hold the collet body with a 9/16” (14 mm) wrench and the collet nut with a 3/4” (19 mm) wrench.
Turn the collet nut to the left and loosen the collet.
Remove the mounted wheel.
WARNING
Disconnect tool from air supply before installing or removing wheel or making any adjustments
NOISE AND VIBRATION READINGS
Catalog
Number
Noise* (Tested in accordance with ISO Standard 15744)
Vibration* (Tested in accordance with ISO Standard 8662-13:1997)
*Sound Pressure (dBA)
*Sound Power (dBA)
Uncertainty (dBA)
*Vibration m/s
2
Uncertainty m/s
2
SDG03S25
83.3
94.9
3.0
3.21
0.91
SDG05S18R
87.4
99.0
3.0
3.22
0.09
SDG05S23
85.1
96.7
3.0
1.98
0.68
SDG7S18F
81.8
93.4
3.0
2.92
0.05
SDG7S25F
79.6
91.2
3.0
2.59
0.08
SDG10S12F
85.9
97.7
3.0
4.52
1.88
SDG10S12R
85.9
97.7
3.0
4.52
1.88
SDG10S18F
80.3
91.9
3.0
2.60
0.04
SDG10S18R
76.4
88.0
3.0
2.63
0.04
SDG10S25F
83.3
94.9
3.0
1.88
0.06
SDG10S25R
81.1
92.7
3.0
2.28
0.05
SDG10SHT08
85.6
97.7
3.0
4.52
0.63
SDG10SHT12
84.0
95.6
3.0
4.45
0.27
SDGS1S12
90.4
102
3.0
2.04
0.17
SDGA1S12
90.9
102.5
3.0
1.19
0.02
SDGS1S18
85.8
97.4
3.0
2.54
0.29
SDGA1S18
87.4
99.0
3.0
1.49
0.10
SDGS1S25
85.1
96.7
3.0
2.10
0.14
SDGA1S25
86.2
97.8
3.0
2.19
0.18
SDGS1S12G
92.8
104.4
3.0
1.21
0.11
SDGA1S12G
91.3
102.9
3.0
0.91
0.06
SDGS1S18G
86.5
98.1
3.0
1.87
0.16
SDGA1S18G
86.8
98.4
3.0
1.79
0.23
SDGS1S25G
82.5
94.1
3.0
2.13
0.11
SDGA1S25G
85.4
97.0
3.0
2.06
0.11
SXG05S18
86.7
98.3
3.0
1.80
0.15
SXG05S23
85.9
97.5
3.0
3.00
1.88
SXG10S12R
83.6
95.2
3.0
3.53
0.14
SXG10S18R
82.2
93.8
3.0
4.40
0.09
SXG10S23R
82.1
93.7
3.0
2.94
0.08
STXG10S