beautypg.com

ParkZone PKZ5080 User Manual

Page 9

background image

15

16

Troubleshooting

The controller will beep more quietly than normal if the

input voltage is below the cutoff voltage when the battery

is connected. Check the voltage of the battery pack to

see if it is correct (charged), or the programmed cutoff

setting if the input voltage is set incorrectly for the

voltage of the pack being used.
If you have trouble arming the controller (and the throttle

trim has been set to minimum), enter the programming

mode and try changing the setting to 1.1ms–1.9ms

in Programming Menu 4 to see if it helps correct the

problem. If it is a computer radio, you may alternatively

increase high and low throttle ATV (endpoint) percentages.

Note: Increasing the high ATV will not have a

consequence on arming issues, only low ATV.

Some transmitters, including all Futaba transmitters, will

require the throttle channel to be “reversed” for proper

operation.

selection or leave in full throttle for 5 seconds to

advance to the next selection.

c. To select 32KHz PWM Frequency – You will hear

3 short beeps. Move the throttle stick to center

(between 1.4 and 1.6ms). The controller will beep

2 times, indicating you have set the program

selection or leave in full throttle for 5 seconds to

advance to the first selection again.

Programming Menu 7 – Operating Mode

The default setting is set to Normal (airplane) Mode,

which is limited to a start-up rate of 0.25 or 1 second.

Alternatively, the Heli Mode can be selected which

reduces the start-up rate to 5 seconds for the first

start-up and any start-up after the motor/ESC has been

stopped for more than 5 seconds. This helps to prevent

damaging the motor, gears or any other components

from an abrupt start-up when none of the parts are

moving. Any time the motor/ESC has been stopped for

less than 5 seconds in Heli Mode, the start-up will be

immediate. This allows power to be applied immediately,

such as when aborting an auto-rotation attempt or for any

other reason, to help prevent a crash. Remember, you

must wait more than 5 seconds after stopping the motor/

ESC in order for the 5-second start-up to occur again.

1. Move the stick to center (between 1.4 and 1.6ms)

for 5 seconds, and the controller will beep 7 times,

indicating you are now in Menu 7.

2. Move the throttle stick to full throttle (>1.7ms)

position to make changes to the Operating Mode

programming.

a. To select Normal Mode – You will hear 1 short

beep. Move the throttle stick to center (between

1.4 and 1.6ms). The controller will beep 2 times,

indicating you have set the program selection or

leave in full throttle for 5 seconds to advance to

the next selection.

b. To select Heli Mode – You will hear 2 short beeps.

Move the throttle stick to center (between 1.4 and

1.6ms). The controller will beep 2 times, indicating

you have set the program selection or leave in

full throttle for 5 seconds to advance to the first

selection again.

Replacement Parts

Make sure that you keep your T-28D Trojan BNF flying. Replacement parts are available at your local hobby shop or from

Horizon Hobby (www.horizonhobby.com). Please try your local hobby shop first. By supporting them, they will be there

when you need them.

Item #:

Description:

PKZ1011

Prop Adapter: T-28D

PKZ1012

Propeller: T-28D

PKZ1031

11.1V 1800mAh Li-Po Battery

PKZ1040

Variable Rate 2- to 3-cell DC Powered Balancing Li-Po Charger

PKZ1060

SV120 Servo (short lead): T-28D Elevator

PKZ1063

Servo Y-Harness: T-28D/3D2

PKZ1064

Metal Gear Set: DSV130M

PKZ1081

SV80 Servo (long lead): T-28D Ailerons

PKZ1090

DSV130M Servo (short lead): T-28D Rudder

PKZ4406

Main Landing Gear: T-28D

PKZ4407

Nose Gear Set: T-28D

PKZ4416

480 Outrunner Brushless Motor: T-28D

PKZ4418

Motor Mount

PKZ4422

Pushrods w/Clevis: T-28D

PKZ5003

Decal Sheet: T-28D

PKZ5013

Clear Canopy & Painted Pilot w/Pedestal: T-28D

PKZ5020

Painted Wing (No Servo): T-28D

PKZ5025

Horizontal Tail w/Accessories: T-28D

PKZ5026

Cowl: T-28D

PKZ5067

Painted Bare Fuselage: T-28D

EFLA1030

30-Amp Pro Switch-Mode BEC Brushless ESC

Optional Parts

Item #:

Description:

PKZ1030

11.1V 2200mAh Li-Po Battery

SPMR5500

DX5e Mode 2 Full Range Transmitter

SPMR6600

DX6i Mode 2 Full Range Transmitter