Dynex DX-LCD26-09 - Manual (Page 14)

14 Appendix
Appendix
To attach a wall mount bracket to your TV:
1 Remove the four M4 screws holding your TV to
the stand.
2 Secure the wall mount bracket to the back of your
TV using four M4 screws, as indicated in the
illustration.
Specifications
Design and specifications are subject to change without notice.
Legal notices
FCC Part 15
This device complies with Part 15 of the FCC Rules. Operation of this product is subject to
the following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
This equipment has been tested and found to comply within the limits for a class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced technician for help.
FCC warning
Changes or modifications not expressly approved by the party responsible for
compliance with the FCC Rules could void the user’s authority to operate this
equipment.
Cables
Connections to this device must be made with shielded cables with metallic RF/EMI
connector hoods to maintain compliance with FCC Rules and Regulations.
Copyright
Manufactured under license from Dolby Laboratories. “Dolby” and
the double-D symbol are trademarks of Dolby Laboratories.
Analog standard NTSC
Digital standard ATSC, 8-VSB, Clear-QAM
Screen 26-inch
Channel coverage VHF: 2-13
UHF: 14-69
CATV: Mid band - A-8 ~ A-1, A ~ I
Super band - J ~ W
Hyper band - AA ~ ZZ, AAA, BBB
Ultra band - 65 ~ 94, 100 ~ 135
Power source AC 100~240 V 50/60 Hz
Power
consumption <120 W
<1 W in standby mode
Audio power 5 W + 5 W internal speaker
S-Video input Y:1 V(p-p), 75 ohm, negative sync
C:0.286 V(p-p) (burst signal), 75 ohm
Video/audio input Video:1 V(p-p), 75 ohm, negative sync
Audio:500 mV(rms)
Component input Y:1 V(p-p), 75 ohm, including sync
Pr/Cr:±0.35 V(p-p), 75 ohm
Pb/Cb:±0.35 V(p-p), 75 ohm
Audio:500 mV(rms)
Suggested resolutions:1080i, 720p,
480p, 480i
HDMI input 1 HDMI input terminal
HDCP compliant
E-EDID compliant
Suggested scan rates:1080i, 720p,
480p, 480i
VGA input D-Sub 15-pin terminal
E-EDID compliant
Suggested scan rates:640×480 /60 Hz,
800×600 /60 Hz, 1024×768 /60 Hz,
1360×768 /60 Hz,
Audio input: Headphone mini-jack for
stereo
Dimensions 25.67 Ч 19.13 Ч 7.4 inches
(65.2 Ч 48.6 Ч 18.8 cm)
Remove stand
Remove M4 screws
M4 screws
20
0 m
m
200 mm
Attach wall
bracket here
Weight 19.4 lbs. (8.8 kg)
Accessories Power cord
User guide
Remote control
Batteries (2 AAA)