Clay Paky TIGER C.C. - Manual

5
• Installing the projector
The projector can be mounted in any position without its operating characteristics
being affected.
IMPORTANT: fix the projector in the desired position utilizing the holes in the
bracket (2).
Secure preferably using a ø10 bolt with nut and lock washer (version HMI 575) -
two ø12 bolts with nuts and lock washers (version HMI 1200).
Make certain that the anchorage is stable before positioning the projector.
IMPORTANT: the safety wire must be secured to the projector and to the support-
ing structure in such a way that if the bracket should fail, the projector will fall as short
a distance as possible. Following any such failure, the safety wire must be replaced
with a genuine Clay Paky spare.
• Minimum distance from target objects
The projector must be positioned in such a way that
objects struck by the beam are separated from the
lens at least by the distance indicated on the lamp
change label against the symbol shown alongside.
• Minimum distance of inflammable materials from any part of the equip-
ment: 0.1 m (4”) for HMI 1200, 0.07 m (3”) for HMI 575.
The appliance may be mounted on surfaces rated normally inflam-
mable.
IMPORTANT: For better and more reliable operation of the projector, the ambient
temperature must not exceed 35° C (95° F). Protection factor IP 20: the appliance is
protected against penetration of solid bodies more than 12mm (0.5”) in diameter
(first digit 2), but can be damaged by spray, jet, drip or rain water (second digit 0).
TIGER C.C.
ENGLISH
HMI 575
HMI 1200
2
4
8
7 6 5
1
3
3
1
POWER SUPPLY AND INTERFACE 2
• Connecting to the electrical power supply
The operations described in this heading must be carried out by a licensed
electrician.
It is good policy to connect projectors to the power supply by way of dedicated switch-
es, so that each can be turned on and off individually from a remote station.
The projector is designed to operate at the voltage and frequency indicated on the
electrical data plate (14) affixed to the rear end.
Check that these two values correspond to the mains voltage and frequency.
IMPORTANT: the projector must be connected to a power supply circuit having
a proper earth system (Class I appliance).
• Connecting the control signals
0-10V CONNECTION
- Independent operation
INSTALLING THE PROJECTOR 1
• Unpacking
Open the box, remove the projector from the packing and place it on a flat, hori-
zontal surface.
Unpack the standard accessories supplied with the equipment. Inspect the lamp
change label (1) and replace it with one of the optional language versions if nec-
essary.
Make certain that the label is never removed, as it displays important safety infor-
mation.
• Initial assembly operations (HMI
575 version)
Position the bracket (2) as required and
secure by tightening the knobs (3). The
bracket can also be fitted on the under-
side of the projector by removing screws
(4) and knobs (3).
• Initial assembly operations (HMI
1200 version)
Position block (5) on the projector
body so that it is aligned with the
threaded holes; secure graduated
plate (6) with eyebolt (7) and then fit
knob (3) and washer (8).
Position bracket (2) on graduated plate
(6) at the desired height; insert bushing
(9), chamfered washer (10) and screw
(11) in the selected hole and tighten
using the supplied Allen key.
The bracket can also be fitted on the
underside of the projector by inverting
the position of graduated plate (6).
If the projector has been shipped with
plate (6) already fitted, before remov-
ing the plate (if necessary) remove the
safety bolt located inside the fixture in
correspondence with eyebolt (7).
Set the projector support in the
desired position and secure by tight-
ening knobs (3).
Fasten the safety wire (12) of lamp
change cover (13) to graduated plate (6).
• Fitting the lamp
Refer to directions for replacement of
the lamp given under heading 6 MAIN-
TENANCE.
9 2 13
12 6 3 10 11
14
• Fitting the safety wire
A safety wire (25) is supplied for use with
version HMI 1200. The wire must be secured
to the gantry or other structure and then
anchored to the eyebolts (7) on the projector
itself.
25
7
(5’ 11”)
1.8 m HMI 575
(8’ 2”)
2.5 m
HMI 1200
0.00 1 0
N
L
Alimentation
0.00 1 0 0.00 1 0
0 - 10V 0 - 10V 0 - 10V
0.00 1 0 0.00 1 0 0.00 1 0
IMPORTANT: Read carefully It is essential for the correct and safe use of the
equipment that erectors and operators should be fully conversant with the
information and instructions given in this manual.
INSTRUCTION MANUAL
ENGLISH
®