Associated Equipment 3HP - Manual (Page 2)

Operating Instructions and Parts Manual
Assembly
'A, A and % Models (See Figure 1, Page 4}
1, Assembly includes the installation of the air baffle, sealing
gasket, discharge bag elbow, dust bag, hose and nozzle,
2, To install the air baffle and sealing gasket, place the unit
upside down on a cardboard covered flat area,
a. Attach the air baffle (13) as shown using included bolts,
b. Remove the paper protection from the sticky side of the
gasket (12) and install on the underside of drum lid/guard
assembly (11), Surface should be clean and dry before
application,
3, Attach bag elbow, filter bag, hose and nozzle,
a. Place the unit right-side up on your container and attach
the discharge bag elbow (4) on the discharge of the
blower as shown in the illustration. Insert and tighten the
included sheet metal screws,
b. Clamp the dust bag (9) on the other end of the elbow
using the clamp enclosed (6),
c. Mount sheet metal reducing adapter (10) to the inlet on
top of drum lid/guard assembly using the squeeze iug to
secure, (li HP Model only),
d. Clamp suction hose (7) to reducing adapter or inlet with
adjustable clamp (8) provided.
e. Clamp nozzle (14) to suction hose with clamp (8),
1, lii, 2 and 3HP Models (See Figure 2, Page 5)
1. Assembly includes the installation of the intake cylinder,
deflector elbow, sealing gasket, discharge bag elbow, dust
bag, hose and nozzle.
2. To install the intake cylinder, deflector elbow and sealing
gasket, place the unit upside down on a cardboard covered
flat area.
a. The deflector elbow (9B) is attached as shown by
removing the two nuts installed at the factory.
b. The intake cylinder (13) is attached as shown using
1/4-20 bolts supplied.
c. Remove the paper protection from the sticky side of the
sealing gasket (11) and install on the underside of the
drum lid (10).
3. Attach bag elbow, filter bag, hose and nozzle (except
3HP Model)*.
a. Place the unit right-side-up on your container and attach
the discharge bag elbow (3A) on the discharge of the
blower as shown in the illustration, insert and tighten the
included sheet metal screws.
b. The dust bag is attached to the removable elbow sleeve
(3C). (This sleeve slips over the end of the elbow and is
held in place with snap-latches.) Clamp the dust bag (8)
to the sleeve (3C) using the clamp (14) enclosed.
IMPORTANT! The edge of the dust bag should be
approximately 1/4" below the flange on fhe sleeve so that
the snap-latches can close completely. If the fabric is too
close to the flange, the snap-latch will rest on the fabric,
and not fully retain the dust bag.
Slip the 6" diameter 0-ring (3B) over the end of the
elbow (ЗА) and seat against the retaining rib. With snap-
latches in a raised position, slide the sleeve (3C) with
attached bag onto the end of the elbow with a slight
twisting motion until tight against the O-ring. Snap the
latches down. (To remove the dust bag for emptying,
snap up the latches and remove the sleeve; reinstall as
above).
c. Mount the sheet metal reducing adapter (7) on the inlet
elbow (9A) using the squeeze lug to secure.
(1HP Model only).
d. Clamp the suction hose (5) to the reducing adapter or
inlet elbow using the adjustable clamp (6) provided.
e. Clamp nozzle (12) to suction hose with damp (6).
Installation
Place the assembled dust collector on the correct diameter
drum (not included). Plastic containers should not be used
as they cannot support the weight of the collector.
Place V j , 'A, and % HP Models on a container having a diameter
of 191i"-20!i".This includes 30-gallon galvanized garbage
cans, or 30-35 gallon open top steel or fiber drums. Do not use
plastic drums.
Place 1, Ti, 2 and 3 HP Models on a container having a
diameter range of 23'-24", such as a standard 55-gallon steel
or fiber drum. Do not use plastic drums.
Check motor rotation on 3-phase power connections; the
cooling fan on the motor should turn clockwise as observed
from above. An electrician can correct rotation by
interchanging any two (3-phase) power lead wires.
Operation
Attach the dust collector inlet hose directly to the connector
built into the dust producing tool. If no built-in connector,
position a hose-end mounted nozzle where it will collect the
dust.
NOTE: Check the recommendation of the tool
manufacturer for the required CFM air flow. The CPM listed in
the specifications for your collector should be greater than the
required CFM to ensure dust collection. See page 7.
Empty the dust collection drum when it becomes half full; if too
full, all dust will be carried into the dust bag.
* See page 6 for filter bag attachment for 3HP Model,