Autostart AS-2460 - Manual (Page 7)

Missing a Start or a Stop Confirmation
4, If you have not received a Start or the Stop confirmation after pressing the ^ button, simply press
the Sbutton. Pressing the M button will refresh the display and will confirm if the vehicle was
started or stopped.
No Start Confirmation Was Received:
If after remote starting the vehicle no confirmation was received, simply press the S button, this
will refresh the display. If the vehicle was started successfully, the ^ icon will appear as well as
the run time countdown. Pressing the S button will also lock all doors (the lock icon will appear).
If the doors were already locked prior to pressing the ^ button, there will be no change in the
status of the doors—i.e. the doors will remain locked.
On models where starter kills were installed, pressing the S button will also activate the starter
kill.
No Stop Confirmation Was Received:
If after remote stopping the vehicle no confirmation was received —i.e. the display did not return to
its basic state— simply press the ^3 button, this will refresh the display. If the engine was
stopped, the ^ icon will disappear and the time will be displayed.
Pressing the S button will also lock all doors (the lock icon will appear). If the doors were already
locked prior to pressing the ^3 button, there will be no change in the status of the doors —i.e. the
doors will remain locked.
button will also activate the starter On models where starter kills were installed, pressing the I
kill.
Multi-_Level Features {defa_uitstate) _________________________________________
The multi-level features allow you to access different features of your vehicle or of a second car by
pressing the shift button once, twice or three times. By default, the multi-level features are
programmed as follows:
Basic Features {press the [IB button 1X)
IB > M .................................................................................
IB > ^ ........................................................
Multi-Car Operation (press the IB button 2X)
IB > B > M ..........................................................................
M > B > S:.....................
M > B > f................
IB > B > |£:....................
.aux 2
. cold weather
. 2" d car lock
. 2" d car unlock
. 2 nd car start/stop
. 2 nd car trunk
Customized Features (press the B button 3X)
(May not be compatible with some vehicles)
Your installer can add customized features such as turning on the radio, opening sliding doors, etc.
M m > ^
IB >|B > IB >
IB >|B > IB >
customized feature 1
customized feature 2
customized feature 3
P. 14 User Guide
Button LCD Sounder
(Channel 4)
Remote-_Sta^rtjiTg_Your Vehicle _____________________ ____ _____________________________
Setting Your Vehicle Into Ready Mode
In order to start the vehicle by remote, the unit must first be set to Ready Mode. If the unit is not set
to Ready Mode, it cannot remote-start the vehicle.
Once the system is set to Ready Mode, the vehicle can be remote-started and stopped at wish.
To set the system to Ready Mode:
1. Ensure that all the doors are closed and that the shifter is in the NEUTRAL position.
2. With the engine already running, apply the parking brake and release the brake pedal.
Make sure to release the brake pedal.
3. Within 20 sec. press lock , unlock or start ; stop on the transmitter.
The parking lights will flash 3 times quickly and remain lit.
4. Remove the key: the engine will go on running.
5. Exit the vehicle and close the door.
6. Press and hold either:
a. lock to lock the doors and shut down the engine;
b. unlock to unlock the doors and shut down the engine;
c. start ; stop to shut down the engine without affecting the doors.
Remaining In Ready Mode
Once the vehicle is in Ready Mode you can start and stop the vehicle at wish. However, should
any of the following occur, the vehicle will exit Ready Mode - thus eliminating the remote start
option until Ready Mode is restored:
• Door opened;
• Hood opened;
• Brake pedal pressed;
• Parking brake disengaged;
• Ignition key turned to the ignition on ( run ) position.
Note: The unit will notify the user that it has exited Ready Mode by giving 3 slow flashes
(parking lights).
Remote starting
Press the ' button for approx. 1 second. The parking lights will come on to inform you that the
remote starter has received your signal. Approximately 5 seconds later, the engine will start. The
parking lights will remain on during the pre-programmed run time of the engine.
If the vehicle does not start at the first attempt, the system will shut down.
Driving Off
With the vehicle running under remote control, press the H button to disarm and unlock the
doors. Enter the vehicle and do the following:
Turn the ignition key to the
ignition on ( run ) position. (Do not turn the key to the crank position
while the engine is running. This would cause the starter motor to re-engage.)
Press the brake pedal to disengage the remote starter unit.
You are now ready to drive off.
Arm! irg_ the Stajter Kill _ ___ __ ___________________
The starter kill (if installed) can be configured by the installer so as to arm automatically (passive
mode) or not to arm automatically (active mode).
User Guide P. 7