Autostart AS-2460 - Manual (Page 5)

The shape of the roof and A-pillars brings about considerable radio-frequency deflection (in this
case the signal from the remote control). As a result, the direction in which the vehicle is facing
in relation to the remote control can affect the range. Straight on - standing in front of the
vehicle - generally gives you the greatest range; the second best performance is from the back.
Using the remote control from either side of the vehicle will usually give the lowest range.
The range will be significantly lower in a crowded parking lot than in open space.
Always hold the transmitter high, approximately at shoulder height. Holding the transmitter
against your chin will also increase your range: your head acts as an antenna.
The operating range will be somewhat lower on vehicles equipped with an aftermarket or factory
alarm.
Diagnostics - Parking Light Flash Table
Flashes Descri ption
1
• Doors locked, starter kill armed.
• Run time has expired.
•
TRUNK button pressed.
• Start signal received by the module.
• Cold weather mode cancelled.
2
• Remote start attempt cancelled by
remote.
• Doors unlocked, starter kill disarmed.
• Exiting ignition valet.
• Exiting remote valet.
• Power-up reset
3
• Entering cold weather mode.
• Extended run time.
• Entering or exiting Ready Mode • Entering ignition valet.
• Entering remote valet.
• Disabling LED
3 slow flashes^ ^after a failed start attempt The module did not detect a tach signal.
4
• +12 V detected on the brake input wire either while cranking or during run time.
• Entering multi-speed tach programming.
• Power ON to OFF
5 Slow • Start attempt failed because no tach signal has been programmed.
5 Fast • Tach signal programmed.
6
• A remote start was attempted while a tach-before-crank signal was detected before
cranking.
8 • Unit reset: occurs when the unit is reset to the factory defaults
10 • A ground (-) signal was detected on the hood pin input wire.
1 —pause—
1—pause—
5 flashes
• Transmitter has been programmed.
[During the transmitter programming procedure]
1 - pause - 2
• There was a remote start attempt while the vehicle was in valet mode.
• Failed start: vehicle's low battery voltage.
ON SOLID for 3
seconds^.
^followed by 1 flash Exiting cold weather mode
^followed by 3 flashes Entering cold weather mode
ON continuously
• Idle mode: Idle mode is engaged
• Run time: The vehicle has been remote started and is in run time.
ON continuously
While the
brake pedal »Confirms that cold weather mode is engaged
is pressed.
ON 2 seconds
• The hood has been opened and a ground (-) signal has been detected on the hood
pin input wire.
ON 4 seconds • Locking or unlocking a door (with Door pulses configured to 4 sec.)
ON 20 seconds • The hood pin has been flashed and you are now in the programming centre.
p. 16 User Guide
7 Backlight Color Menu COLOR
Backlight There 8 different colors Blue lights is default
8 LCD On Menu LCD
LCD on time OFF 01 1 min, 15min, 30 min, 60min and ON
OFF 15 1 min is default.
OFF 30
OFF 60
ON
9 Clock Menu CLOCK
Clock hour 12:00 Adjust clock hour
12 is flashing. (value from 0 to 12)
Clock minute 12:00 Adjust clock minute
00 is flashing. (value from 0 to 60)
10 Temperature Menu TEMP
Temperature CTEMP Deg Celsius or Fahrenheit
Or Deg. Celsius is default
FTEMP
11 Language Menu LANGU
Language ENG
Or English is default.
FRAN
12 F Button Function FBPRO F Button Programming
Menu
FB programming 1 23M
231 M
21 3M
31 2M
M1 23
Parking Countdown
This version of the countdown feature is particularly useful for keeping track of parking meter time:
the user may quickly set up the countdown using the Parking Menu. The transmitter will beep once,
5min before the Parking countdown reaches 0.
Alarm Clock
The LCD remote control has a built-in alarm clock, which can be set up using the Alarm Clock
Menu. Once the programmed time is reached, the remote will beep 6 times every minute until a
button is pressed.
CWM menu:
When this feature is enabled, press li for 3sec to enter or exit Cold Weather mode. If disabled.
H e —>• ^ button to enter or exit Cold Weather mode. press L
Valet menu:
When this feature is enabled, press to enter Valet mode. When this feature is disabled, press
H+ ^ buttons simultaneously.
Time start menu:
This feature is used to remote start the carat a pre-programmed time. Once the pre-programmed
time is reached, the remote will send a start command to the car module.
Secure Remote feature:
This feature is used to lock the keypad of the transmitter to avoid accidental button press. When
the remote is locked and a button is pressed, the LCD will display “PRESF” for 1 second and goes
back to the clock.
User Guide P. 5