Autostart AS-6850VTW-FM User Manual

Page 3

Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".

Virtual Tach System

•

Virtual Tach System combines the latest microcontroller technology and a complex algorithm that took years to develop.

VTS is able to effectively monitor the engine starting sequence and release the starter at the right time without physically

connecting the tach wire to the remote starter. The VTS constantly monitors the data and readjusts itself automatically in order

to maximize its capability to start the engine properly in any weather or deteriorating battery condition

(automatic transmission

only).

Optional Time Delay Adjustment in Virtual Tach System

Follow these steps to program crank time adjustment, if needed:

Flash the hood pin (see p. 1) — the parking lights will stay on for up to 20 seconds.

Before the lights go out, press and hold the brake pedal and press the

lock

and

unlock

buttons simultaneously — the

parking lights will flash 4 times.

Do not release the brake pedal.

Press the

lock

button if you wish to increase the time delay or the

unlock

button if you want to decrease it.

The time

delay will be increased or decreased by 50ms. and the parking lights will flash once every time the

lock

unlock

button is pressed.

4. Press the

trunk

button to save the settings you have entered.

5. Release the brake pedal - the time delay programming is now complete.

Multi-speed Tach Programming

. Flash the hood pin (see p. 1) — the parking lights will stay on for up to 20 seconds.

2. Before the lights go out, press and hold the brake pedal and press the

lock

and

unlock

buttons

simultaneously — the

parking lights will flash 4 times and the siren or horn will chirp 4 times. At that point, release the brake pedal.

3. Start up the engine and allow the vehicle to reach regular engine idle speed.

4. Once the engine is running at normal idle speed, press the brake pedal and keep it down

until you hear the parking lights

output click 5 times; the siren will chirp twice.

5. Release the brake pedal —^the tach programming is now complete.

Slren/Horn Honk Timing

Follow these steps to program horn confirmation:

1. Ensure that the hood is up and that the ignition is off.

•

Hold the hood pin down for 4 seconds.

•

Release the hood pin. The parking lights will come on.

•

While the parking lights are on, immediately push and release the hood pin again. ^— The parking lights will stay on for up to

20 seconds.

Press and hold the brake pedal, then simultaneously press the

unlock

and

start

stop

buttons — the horn will chirp 5

times.

3. Release the brake pedal.

4. To change the timing:

To increase the Horn pulse by 3 ms, press the

lock

button.

To decrease the pulse by 3 ms, press the

unlock

button.

To increase the pulse by 10 ms, press the

start

stop

button.

To decrease the pulse by 10 ms, press the

trunk

button.

5. To save the new settings: press

lock

and

unlock

. If 3 chirps are returned, the new settings have been saved.

Supplementary Information

Fifth Relay Output (2nd IGN, ACC or CRANK)

http://www.autostart.ca

Installation Guide

function

4 - AUX 3 Programming

option

Constant while the TRUNK button is pressed, disarm and passive rearm after 30 sec.

OPTION 2

1-sec. output when TRUNK button is pressed for 3 sec. while ignition is OFF, disarm and

passive rearm after 30 sec. & data output (channel expander MCX-100 enabled)

function

5 - AUX 2 Programming

option

1* Car Finder

OPTION 2 AUX Toggle with 30-sec. time out — Using FUNCTION then LOCK buttons.

OPTION 3 AUX constant while pressed — Using FUNCTION then LOCK buttons.

MODE 2

‘

indicates

default

setting

function

1 - Home Valet

OPTION 1

OPTION 2*

function

2 - Safe Start

OPTION 1

OPTION 2*

OPTION 3

Home valet ENABLED

Home valet DISABLED

Safe start ENABLED

Safe start DISABLED

“Swap Start” - enhanced safe start mode with extended safety: To start the engine: press

FUNCTION button then LOCK button. To trigger AUX 2: press START/STOP

FUNCTION 3 - Engine Run Time

OPTION 1

Run time = 3 minutes in gas mode / 8 minutes diesel mode

OPTION 2*

Run time = 15 minutes in gas mode / 20 minutes diesel mode

OPTION 3 Run time = 25 minutes in gas mode / 30 minutes diesel mode

OPTION 4 Temperature run time

FUNCTION 4 -Idle Mode & Turbo Mode (auto) / Turbo Mode (manual)

OPTION 1 Idle mode & turbo mode DISABLED (AUTO) / turbo mode DISABLED (MANUAL)

OPTION 2*

Idle mode & turbo mode ENABLED (AUTO) / turbo mode DISABLED (MANUAL)

OPTION 3

Idle mode & turbo mode ENABLED (AUTO) / turbo mode ENABLED (MANUAL)

FUNCTION 5 - Engine type and Cold Weather Mode

OPTION 1 Diesel mode with 20-minute run time in cold weather mode (30-sec. wait to start delay)

OPTION 2*

Gas mode with 3-minute run time in cold weather mode

OPTION 3

Diesel mode with 8-minute run time in cold weather mode (18-sec.

wait to start delay)

OPTION 4

Diesel mode with 8-minute run time in cold weather mode (7-sec. wait to start delay)

MODE 3

‘

indicates

default

setting

function

1 - Chirps

OPTION 1

OPTION 2*

OPTION 3

OPTION 4

function

2 - Arming

OPTION 1

OPTION 2*

OPTION 3

OPTION 4

Warning chirps only - Lock confirmation upon 2

press of LOCK button

Chirps

enabled

Chirps

enabled

with open-zone notification

(siren / horn warning 10 sec. after arming if a door is opened)

Chirps

disabled

- Lock confirmation upon 2

press of LOCK button

Active arming

Passive arming (30 sec.) (*two-stage disarm)

Passive arming (30 sec.) (*single-stage disarm)

Active arming with disarm notification

FUNCTION 3 - Ignition monitoring with Siren / Horn mode

OPTION 1 Siren mode with ignition monitoring DISABLED

OPTION 2* Siren mode with ignition monitoring ENABLED

OPTION 3

Horn mode with ignition monitoring DISABLED

OPTION 4

Horn mode with ignition monitoring ENABLED

FUNCTION 4 - Shock Sense / Warn-away

OPTION 1

Shock Sense - DISABLED / Warn Away - DISABLED

OPTION 2*

Shock Sense - ENABLED / Warn Away - ENABLED

OPTION 3

Shock Sense - ENABLED / Warn Away - DISABLED

OPTION 4

Shock Sense - DISABLED / Warn Away - ENABLED

FUNCTION 5 - Ignition Valet

OPTION 1 Ignition valet — DISABLED

OPTION 2* Ignition valet — ENABLED

MODE 4

‘

indicates

default

setting

function

1 - Relock

OPTION 1

disabled

OPTION 2*

enabled

- Relocks all doors 60 seconds after unlocking if neither doors nor trunk

are opened

function

2 - Pager (Pager sold separately)

OPTION 1

Pager ENABLED

OPTION 2*

Pager DISABLED

function

3 - Ready Mode Option

OPTION 1

Enabled by handbrake

OPTION 2*

Enabled by remote

Installation Guide

http://www.autostart.ca/

P. 6

P. 3