Black & Decker 5027 - Manual (Page 4)

IMPORTANT SAFETY INSTRUCTIONS CONT.
19. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that
is damaged should be carefully checked to determine that it will operate properly and
perform its intended function. Check for alignment of moving parts, binding of moving
parts, breakage of parts, mounting, and any other conditions that may affect its
operation. A guard or other part that is damaged should be properly repaired or
replaced by an authorized service center unless otherwise indicated elsewhere in this
instruction manual. Have defective switches replaced by authorized service center.
Do not use tool if switch does not turn it on and off.
20. AVOID USING A POWER TOOL FOR APPLICATIONS OTHER THAN THOSE
SPECIFIED. Never use a power tool for applications other than those specified in the
instruction manual.
21. ENSURE SAFE OPERATION THROUGH CORRECT HANDLING. Secure safe
operation through correct handling by observing the instructions described herein. Do
not employ accessories other than those specified herein; otherwise, a hazardous
condition may be created. Never allow a power tool to be used by persons not familiar
with correct handling (such as children) or by those who cannot handle the tool
correctly.
22. CONFIRM THAT NO ITEMS SUCH AS AN ELECTRIC CABLE OR CONDUIT ARE
BURIED INSIDE. In places where live wiring may be hidden behind a wall, floor,
ceiling, etc. do not hold or contact any metal parts of the tool. In such cases, metal parts
could become electrically live and present a serious shock hazard.
23. KEEP THE RIGHT PARTS IN THE RIGHT POSITIONS. Do not remove covers and
screws which have been factory-mounted. They perform important respective roles.
Keep them in the right positions.
24. SHOULD THE PLASTIC HOUSING OR HANDLE OF A POWER TOOL BE
CRACKED OR DEFORMED, DO NOT USE IT. Since cracked or deformed parts may
lead to an operator receiving an electric shock, do not use such a power tool.
Immediately have it repaired.
25. DO NOT WIPE PLASTIC PARTS WITH SOLVENT. Solvents such as gasoline,
thinner, benzine, carbon tetrachloride, and alcohol may damage and crack plastic
parts. Do not wipe them with such solvents. Wipe plastic parts with a soft cloth lightly
dampened with soapy water.
26. ALWAYS KEEP THE MOTOR AIR VENT FULLY CLEARED. A constantly open
motor air vent is necessary to allow air to come in and out for cooling the motor. Do
not allow it to become clogged up, even if dust is blown through it.
27. OPERATE POWER TOOLS AT THE RATED VOLTAGE. Operate power tools at
voltages specified on their nameplates.
28. NEVER TOUCH THE MOVING PARTS. Never touch the moving parts such as
blades, bits, cutters and others.
29. STOP OPERATION IMMEDIATELY IF ANY ABNORMALITY IS DETECTED.
Should a power tool be detected as out of order or should other abnormalities be
observed during operation, stop using the tool immediately.
30. NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF. Don’t leave
tool until it comes to a complete stop.
31. CAREFULLY HANDLE POWER TOOLS. Should a power tool be dropped or struck
against hard materials inadvertently, it may be deformed, cracked, or damaged.
SAVE THESE INSTRUCTIONS
Accessories
CAUTION: Recommended
accessories for this Electric Power
Tool are listed in this manual. The
use of any other attachment or
accessory might be hazardous.
The accessories listed in this
manual are available at extra cost
from your local dealer or Black &
Decker Service Center.
A complete listing of service
centers is included on the owner’s
registration card packed with your
tool.
If you need assistance in
locating any accessory please
contact:
Black & Decker (U.S.) Inc.
User Services Department
626 Hanover Pike
P.O. Box 618
Hampstead, MD 21074-0618
Standard Accessories
Hexagon Bar Wrench 10mm (M21)
Hexagon Bar Wrench 6mm (M8)
Side Handle
Hexagon Bar Wrench 4mm (M5)
Bolt
Spring Lock Washer
Optional Accessories
(sold separately)
Bull Point
o
Totallength: 20-1/2”
Cold Chisel
Total length: 20-1/2"
Cutter
Total length: 20-1/2" Width 3”
Scoop