MTD 242-685-000 - Manual (Page 11)

Models 675, 685 and 689
PARTS LIST FOR MODELS 675, 685, 689, 241677 and 241687 POWER VACUUMS
REF.
NO.
PART
NO.
CODE DESCRIPTION
REF.
NO.
PART
NO.
CODE DESCRIPTION
1 05778 Clutch Grip Ass’y-t 43 — Engine
2 711-0679 Clevis Pin .375" Dia. x 1.88"t 46 748-0201 Spacer .63" I.D. x .88" O.D. x
3 747-0154 Clutch Rod 32" Lg.t 56" Lg.t
4 749-0787 Handle Brace (Painted) 47 14530 638 Side Plate
749-0482 Handle Brace (Chrome) 48 715-0247 Spring Pin Spiral 3/16" Dia. x
5
—
Part of Engine 1" Lg.t
6 710-0892 Hex Wash. Hd. AB-Tap Scr. 49 748-0288 Drive Piniont
1/4" X .62" Lg.t 50 710-0170 Hex Locking Bolt 5/16-24 x
7 14558 Belt Guardt .62" Lg.
8 714-0114 Square Key 1/4" x 2" Lg. 51 736-0159 FI-Wash. .34" I.D. X .87" O.D.
9 14536A Air Vane Plate Ass’y- 53 734-1035 Wheel Ass’y. Comp. 12" x3"
(675 and 677)t (Incl. Ball Bearings)
14557A Air Vane Plate Ass’y- w/Pulley 734-1184 Wheel Ass’y. Comp. 10.5" x 4"
10 710-0442 Hex Bolt 5/16-18x1.5" Lg.* (677 Only)
11 754-0219 “V”-Beltt 741-0313 Bearings (677 Only)
12 736-0119 L-Wash. 5/16" I.D.* 54 750-0194 Spacer .63" I.D. x 1.0" O.D. x
13 712-0267 Hex Nut 5/16-18 Thd.* .94" Lg. (675, 685, 687)
14 16454 638 Engine Mounting Frame Ass’y. 748-0192 Spacer .63" I.D. x .878" O.D.
15 714-0115 Cotter Pin 1/8" Dia. x1" Lg.* X .79" Lg. (677)
16 736-0187 FI-Wash. .63“ I.D. x 1.25" O.D. 55 710-0118 Hex Bolt 5/16-18 X .75" Lg.*
17 736-0921 L-Wash. 1/2" I.D.* 57 747-0542 Height Adjustment Crank
18 712-0206 Hex Nut 1/2-13 Thd.* 58 736-0117 FI-Wash. .385" I.D. x .62" O.D.
19 712-0107 Hex Cent. L-Nut 1/4-20 Thd. 59 720-0171 Crank Knob
20 732-0411 Extension Spring .78" O.D. x 61 710-0136 Hex Bolt 1/4-20 x 1.75" Lg.
.75" Lg.t 62 764-0162A Vacuum Bag—Felt
21 734-1036 Swivel Caster Wheel 5" Dia. x 63 1539-019 Push Speed Nut .25" Dia. Stud
1.25" 64 749-0785 Lower Handle (Painted)
22 732-0409 Extension Spring .38" O.D. x 749-0481 Lower Handle (Chrome)
7.50" Lg.t 66 726-0100 Push Nut 3/8" Dia.
23 716-0104 Snap “E”-Ring .50" Dia. Shaftt 67 711-0737 Stud Pin .250" Dia. x 1.75"
24 756-0367 “V”-Pulley 5/8" X 6.50" O.D.t 69 714-0145 Internal Cotter Pin 3/8" Dia.
25 748-0142 Flange Bearing .502" I.D.t 70 749-0786 Upper Handle (Painted)
26 14570 Gear Box Mounting Brackett 749-0480 Upper Handle (Chrome)
27 732-0376 Extension Spring .75" O.D. x 71 738-0185 Rear Axle
3.28" Lg.t 72 715-0249 Spring Roll Pin 5/32" Dia. x
28 14565 Clutch Bracket Ass’y. t 1.12t
29 714-0229 #2 Woodruff Key 3/32" Dia. x 73 750-0142 Spacer .82" I.D. X 1.0" O.D.
.81" Lg.t X .305 Lg.t
30 748-0227A N Hex Flange Bearing Bronze 74 736-0175 L-Wash. .265" I.D.t
.625" I.D.t 75 710-0352 Hex Self-Tap Scr. 1/4" x 3/8"
31 738-0516 Pinion Shaft .50" Dia. x 5"t Lg.t
32 717-0493 Gear Box Ass’y. Comp.t 76 14556 R.H. Pinion Guardt
33 16273 Caster Arm Ass’y. 14555 L.H. Pinion Guard (Not Shown)
34 08348 Drive Shaftt 77 712-0298 Hex Jam Nut 1/4-20 Thd.t
35 748-0136 Bevel Gear .50" I.D. x 14 Teeth 78 736-0242 Belleville Washer
36 748-0108 Flange Bearing .503" I.D.t 79 736-0300 FI-Wash. .35" I.D. x .87" O.D.
37 08189 Gear Boxt 80 750-0528 Spacer .38" I.D. x .50" O.D. x
38 748-0110 Flange Bearing .630" I.D.t .18" Lg.
39 08187 Gear Box Covert 81 711-0797 Ferrule 3/8-8 x .38" Dia.
40 748-0135 Bevel Gear .62" I.D. x 28 Teetht 82 712-0354 Hex Nut 3/8-8 Thd.
41 715-0246 Spring Pin Spiral 3/16" Dia. x 83 736-0169 L-Wash. 3/8" I.D.*
1.25" Lg.t
42 710-0726 Hex Wash. Hd. AB-Tap Scr.
5/16" X. 75" Lg.
fParts for Self-Propelled Units (Models 685, 689 and 241687) Only.
*For faster service obtain standard nuts, boits and washers iocaiiy.
if these items cannot be obtained iocaiiy, order by part number and
size as shown on parts list.
638-Red; 629-Silver Flake; 498-Yellow
CODE: N notates a new part (not previously existing). A three digit
number is the color code. Specify color code if color or finish is
important when ordering parts, [i.e., (part no.)-638 for Red
Finish],
11