Enter your age, Follow your progress with the displays, When the program has ended, remove the key – NordicTrack NTTL17900 User Manual
Page 18: O o c
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".

Enter your age.
Three seconds after the pulse-driven program is
selected, the words “ENTER AGE” and the current
age setting will appear in the main display. You
must enter your age to use the pulse-driven program.
INQINI:
Ci C=l rAl.OklfS CZIIIME' CZI PACK
SFFEO
1 n
C 1 T
C O O iT C
D n
n
I.U
M
i
M M u L. L. U
u.
□□ :.AP5
□□ -FART W? □ SFG¥EN" TIN'F
If you have already entered your age, go to step 5.
If you have not entered your age, press the Enter
Age buttons to enter your age. The buttons can be
held down to enter your age quickly. Your age will
then be saved in memory.
Press the Start Program button or the Speed +
button to start the program.
A moment after the button is pressed, the tread
mill will automatically adjust to the first speed and
incline settings for the program. Hold the handrails
and begin walking.
The pulse-driven program is divided into several
time segments of different lengths. The main dis
play will show both the time remaining in the pro
gram and the time remaining in the current seg
ment of the program. One target heart rate setting
is programmed for
___ c
Current Segment ____
0 0
(
o o c
0 0
(
o o c
o o d
) 0 0 0 0 0 0 0 0 0 0 0 0 0
J O O O O O O O O O O O O O
l O O O O O O O O O O O O O
) 0 0 0 0 0 0 0 0 0 0 0 0 0
J O O O O O O O O O O O O O
each segment. The
target heart rate
setting for the first
segment will be
shown in the flash
ing Current
Segment column of
the program display. The target heart rate settings
for the next thirteen segments will be shown in the
thirteen columns to the right.
When only three seconds remain in the first seg
ment of the program, both the Current Segment
column and the column to the right will flash, a se
ries of tones will sound, and all target heart rate
settings will move one column to the left. The tar
get heart rate setting for the second segment will
then be shown in the flashing Current Segment
column. As you exercise, the speed and/or incline
of the treadmill will automatically change as
needed to keep your heart rate near the current
target heart rate setting.
The program will continue until the target heart
rate setting for the last segment is shown in the
Current Segment column and no time remains in
the program. The walking belt will then slow to a
stop.
If the speed or incline setting for the current seg
ment is too high or too low, you can adjust the set
ting with the Speed or Incline buttons. However, if
you decrease the speed, the incline will automati
cally increase: if you increase the speed, the in
cline will decrease. If you increase the incline, the
speed will decrease; if you decrease the incline,
the speed will increase. The treadmill will always
attempt to keep your heart rate near the target
heart rate setting for the current segment. Note:
When the incline reaches the lowest setting, the
speed cannot be increased any further. When the
incline reaches the highest setting, the speed can
not be decreased any further.
If your pulse is not detected during the program,
the letters “PLS” will flash in the main display and
the speed and incline of the treadmill may auto
matically decrease until your pulse is detected. If
this occurs, refer to the instructions included with
the optional chest pulse sensor.
To stop the program, press the Stop button. The
pulse-driven program should not be stopped tem
porarily and then restarted. To use the pulse-dri
ven program again, reselect the program and start
it at the beginning.
Follow your progress with the displays.
Refer to step 5 on page 11.
When the program has ended, remove the key.
See step 6 on page 13.
18