MTD 243-600 - Manual (Page 3)

PARTS LIST FOR 243-600 EDGER
Ref.
No.
Part
No.
Color
Code
Description
New
Part
Ref.
No.
Part
No.
Color
Code
Description
New
Part
1 720-142 Flat Bar Grip 39 10244 Clamp Bracket
2 9948 Clutch Handle Assembly 40 9944-463 Belt Guard Assembly
3 710-106 Hex Head Cap Screw 41 736-329 Spring Lockwasher % Screw *
K-20x1>i Lg. * 42 710-179 Hex Head Thread Cut Screw
4 9950 Clutch Plate type“F”)4-20xJ/2Lg. *
5 732-171 Compression Spring 43 9934 Spindle Housing t
6 736-264 Flat Washer * 44 711-385 Spacer
7 712-372 Hex Centerlock Nut 18 Thd. * 45 711-384 Spindle
8 714-474 Cotter Pin Vt Dia. * 46 736-116 Flat Washer .625 I.D. x .937 O.D. *
9 9951 Clutch Rod 47 711-420 Pulley-Spindle
10 10113-463 Handle Cover 48 715-246 Spirol Pin % Dia. xV/i" Lg. *
11 Engine 49 738-213 Axle Bolt—Front Wheel
12 714-105 Square Key .187 sq. x 1 ” Lg. * 50 9392-513 Wheel Assembly
7"
Dia.—Front
13 711-421 Pulley—Engine 51 712-267 Hex Nut %— 18 Thd.
14 9941-463 Belt Guard Assembly 52 736-119 Spring Lockwasher Screw *
15 736-114 Internal Lockwasher Dia. * 53 715-111 Spirol PinKa" Dia.x 1" Lg. *
16 710-121 Hex Head Cap Screw 54 711-386 Spacer
^2-20 X Lg. 55 711-110 Shoulder Bolt
17 748-227 Hex Bearing 56 712-114 Castle Hex Nut
'A-20
Thd. *
18 710-442 Hex Head Cap Screw 57 736-105 Belleville Washer *
Ji6-18xiy2" Lg. 58 711-207 Lock Handle
19 754-142 V-Belt%"x31.2Lg. * 59 711-382 Shaft
20 710-402 Hex Head Cap Screw 60 9392-514 Wheel Assembly 8" Dia.—Rear (2)
?i6-18x4y2"Lg. 61 7006 Fortiflex Bearing
21 711-379 Bushing 62 738-108 Axle Bolt—Rear
22 732-187 Compression Spring 63 736-169 Spring Lockwasher for
Vs"
Screw *
23 9932 Pivot Bracket Assembly 64 712-798 Hex Nut%-16Thd. *
24 9946 Lever Assembly 65 9930-463 Base Assembly
25 736-112 Belleville Washer * 66 9936-463 Wheel Bracket Assembly
26 715-119 Roll Pin ^ 2 "
X
3/4" Lg.* 67 9955 Handle—Lower
27 9953 Cam Lever 68 746-145 Cable Clip
28 9938-463 Guard Assembly 69 710-111 Carriage Bolt
A—20
x 154 Lg. *
29 711-383 Stud 70 736-329 Spring Lockwasher 54"Screw*
30 712-107 Hex Centerlock Nut K—20 Thd. * 71 712-287 Hex Nut 54-20 Thd. *
31 9952 Guide 72 10112 Handle—Upper
32 712-101 Roll Pin %"x1K2"Lg.* 73 10449 Throttle Control Complete
33 732-188 Tension—Spring 74 732-200 Conduit and Wire **
34 710-444 Hex Head Cap Screw 77 7470 Knob **
%-18x1"Lg. *
78 710-606 Hex Head Cap Screw
35 9954 Blade 54-20x 154 Lg. *
36 712-200 Hex Elastic Stop Nut >2—20 Thd. * 79 718-124 Grip — Handle
37 712-922 Hex Jam Nut
'4—20
Thd. * 80 710-137 Set Screw
%—
24 Thd. *
38 741-124 Bearings #203
*For faster service order standard nuts, bolts, and washers locally. If these items cannot be obtained locally, order by
part number and size as shown on parts list.
463 — Top Flite Red — When ordering parts, if color or finish is important, use the appropriate color code shown at
left. (e.g. Top Flite Red 10112 (463))..
tTo order spindle housing complete with two bearings, spacer and spindle shaft order part number 10229.
^*Part of throttle control complete 10449.
The engine is not under warranty by the
edger manufacturer. If repairs or service is
needed on the engine, please contact your
nearest authorized engine service outlet.
Check
the "Yellow Pages" of your
telephone book under "Engines —
Gasoline."
Find utfastinthn