SINGER 147-60 - Manual (Page 3)

INSTRUCTIONS FOR ORDERING
In ordering from tluK list, nse ONLY the part NUMBER
in the FIRST column.
The number stamped on a Sewing Machine Part is in every
case the number of the single part only.
Every cond)ination of parts sent out as such has ils .specific
number, which, although not stamped on the parts, must be
used when ordering the combination.
Each number always indicates the SAME PART in whatever
list it a|)pears, or for whatever machine.
The letters after some of the numbers indicate the style of
finish oidy, as follows;
A—Ifardened, Polished, Nickel Plated and Buffed
B—Polished, Nickel Plated and Buffed
C—Ifardened Only
D—Polished Only
E—Soft, Not Polished
F—Hardened and Polished
II—Blued
,T—Nickel Plated Only
K—llard<‘ned and Nickel Plated
L—Brass Pl.ated
M—Oxidized
N—JapaniHsl, Dull
P—.Japanned, Bright
R—Miulized
1 '—Co])per I’laled
T. A.—Jlardened, Polished, Copper and Nickel Plated
and Buffed
T. B.—Copper and Nickel Idated and Polished
T. J.—Copper and Nickel Plated Only
T. K.—Hardened, Copper and Nickel Plated
T. M.—Copiier Plated and Oxidized
T. L.—Copper and Brass Plated
IJ—Zinc Plated
V —Silver Plated
W—Polished and Nickel Plated
Z—Chronumn Plated
Z. B.—Polished, Nickel Plated, Buffed and Chromium Plated
Z. J.—Nickel and Chronnum Plated
These letters MUST BE USED when they appear in the list;
and AFTER the number as in the list.
In this .series:
1 to LWO and .'iOOOl to .51500 are Screw Numbers
1.501 to 1800 and 51501 to 51800 are Nut Numbers
1801 to 2000 and 51801 to ,52000 are Roller Numbers
2001 to 50000 and 52001 and upward are numbers of
Machine Parts
The figures in the s(!cond column refer only to the plates,
illustrating the parts, and are NOT TO BE USED in ordering.
Parts marked with an asterisk (*) are furnished only when
repairs are made at factory.
When ordering ]>arts which differ as to Gauge (the distance
between .seams) the Gauge, as well as the Number must be
given on order.
LIST OF PARTS COMPLETE
FOR
MACHINE No, 147-60
FOR LAP SEAMING SHIRT SLEEVES OF LIGHT WEIGHT MATE­
RIALS AND WORK OF A SIMILAR NATURE. TWO NEEDLES,
TWO LOOPERS. GAUGES IN. TO 'A IN. SHORT NEEDLE
BAR AND LOOPER STROKE.
THE LOOPERS ARE ARRANGED SO THAT THEY MAY BE THROWN
OUT OF POSITION FOR CONVENIENCE IN THREADING.
AN IMPROVED OILING SYSTEM AUTOMATICALLY OILS ALL
OF THE PRINCIPAL BEARINGS OF THE MACHINE. BAUNCE
WHEEL N0. 64259. DIAMETER OF BELT GROOVE 2
INCHES. SPEED 4300.
NO. 1‘L.VTB NAME
*68127 -------------- Arm, upper and lower (solid) with 1)48 j ,
08483 and four 131022..................................
68428 9917 Ann Bottom Cover.................................................................
68429 9917 “ “ “ Gasket (cork)............................
1057 e 20503 “ “ “ Screw.........................................
68350 9922 “ Oil Cup for oiling Arm Rock
Shaft Front Bearing....................................................
68430 9922 Arm Oil Cup for filling oil reservoir....
54648 9922 “ “ “ Oil Pad (braided cotton)
for 68350......................................................................
68431 9916 Arm Rock Shaft.....................................................................
68432 ------ “ “ “ 68431 with 1235 f and
68439............................................................................